Staging
v0.8.1
v0.8.1
https://github.com/torvalds/linux
Tip revision: 830b3c68c1fb1e9176028d02ef86f3cf76aa2476 authored by Linus Torvalds on 11 December 2022, 22:15:18 UTC
Linux 6.1
Linux 6.1
Tip revision: 830b3c6
sm8450.dtsi
// SPDX-License-Identifier: BSD-3-Clause
/*
* Copyright (c) 2021, Linaro Limited
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-sm8450.h>
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/clock/qcom,sm8450-camcc.h>
#include <dt-bindings/dma/qcom-gpi.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/mailbox/qcom-ipcc.h>
#include <dt-bindings/power/qcom-rpmpd.h>
#include <dt-bindings/interconnect/qcom,sm8450.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
#include <dt-bindings/thermal/thermal.h>
/ {
interrupt-parent = <&intc>;
#address-cells = <2>;
#size-cells = <2>;
chosen { };
clocks {
xo_board: xo-board {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <76800000>;
};
sleep_clk: sleep-clk {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <32000>;
};
};
cpus {
#address-cells = <2>;
#size-cells = <0>;
CPU0: cpu@0 {
device_type = "cpu";
compatible = "qcom,kryo780";
reg = <0x0 0x0>;
enable-method = "psci";
next-level-cache = <&L2_0>;
power-domains = <&CPU_PD0>;
power-domain-names = "psci";
qcom,freq-domain = <&cpufreq_hw 0>;
#cooling-cells = <2>;
L2_0: l2-cache {
compatible = "cache";
next-level-cache = <&L3_0>;
L3_0: l3-cache {
compatible = "cache";
};
};
};
CPU1: cpu@100 {
device_type = "cpu";
compatible = "qcom,kryo780";
reg = <0x0 0x100>;
enable-method = "psci";
next-level-cache = <&L2_100>;
power-domains = <&CPU_PD1>;
power-domain-names = "psci";
qcom,freq-domain = <&cpufreq_hw 0>;
#cooling-cells = <2>;
L2_100: l2-cache {
compatible = "cache";
next-level-cache = <&L3_0>;
};
};
CPU2: cpu@200 {
device_type = "cpu";
compatible = "qcom,kryo780";
reg = <0x0 0x200>;
enable-method = "psci";
next-level-cache = <&L2_200>;
power-domains = <&CPU_PD2>;
power-domain-names = "psci";
qcom,freq-domain = <&cpufreq_hw 0>;
#cooling-cells = <2>;
L2_200: l2-cache {
compatible = "cache";
next-level-cache = <&L3_0>;
};
};
CPU3: cpu@300 {
device_type = "cpu";
compatible = "qcom,kryo780";
reg = <0x0 0x300>;
enable-method = "psci";
next-level-cache = <&L2_300>;
power-domains = <&CPU_PD3>;
power-domain-names = "psci";
qcom,freq-domain = <&cpufreq_hw 0>;
#cooling-cells = <2>;
L2_300: l2-cache {
compatible = "cache";
next-level-cache = <&L3_0>;
};
};
CPU4: cpu@400 {
device_type = "cpu";
compatible = "qcom,kryo780";
reg = <0x0 0x400>;
enable-method = "psci";
next-level-cache = <&L2_400>;
power-domains = <&CPU_PD4>;
power-domain-names = "psci";
qcom,freq-domain = <&cpufreq_hw 1>;
#cooling-cells = <2>;
L2_400: l2-cache {
compatible = "cache";
next-level-cache = <&L3_0>;
};
};
CPU5: cpu@500 {
device_type = "cpu";
compatible = "qcom,kryo780";
reg = <0x0 0x500>;
enable-method = "psci";
next-level-cache = <&L2_500>;
power-domains = <&CPU_PD5>;
power-domain-names = "psci";
qcom,freq-domain = <&cpufreq_hw 1>;
#cooling-cells = <2>;
L2_500: l2-cache {
compatible = "cache";
next-level-cache = <&L3_0>;
};
};
CPU6: cpu@600 {
device_type = "cpu";
compatible = "qcom,kryo780";
reg = <0x0 0x600>;
enable-method = "psci";
next-level-cache = <&L2_600>;
power-domains = <&CPU_PD6>;
power-domain-names = "psci";
qcom,freq-domain = <&cpufreq_hw 1>;
#cooling-cells = <2>;
L2_600: l2-cache {
compatible = "cache";
next-level-cache = <&L3_0>;
};
};
CPU7: cpu@700 {
device_type = "cpu";
compatible = "qcom,kryo780";
reg = <0x0 0x700>;
enable-method = "psci";
next-level-cache = <&L2_700>;
power-domains = <&CPU_PD7>;
power-domain-names = "psci";
qcom,freq-domain = <&cpufreq_hw 2>;
#cooling-cells = <2>;
L2_700: l2-cache {
compatible = "cache";
next-level-cache = <&L3_0>;
};
};
cpu-map {
cluster0 {
core0 {
cpu = <&CPU0>;
};
core1 {
cpu = <&CPU1>;
};
core2 {
cpu = <&CPU2>;
};
core3 {
cpu = <&CPU3>;
};
core4 {
cpu = <&CPU4>;
};
core5 {
cpu = <&CPU5>;
};
core6 {
cpu = <&CPU6>;
};
core7 {
cpu = <&CPU7>;
};
};
};
idle-states {
entry-method = "psci";
LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
compatible = "arm,idle-state";
idle-state-name = "silver-rail-power-collapse";
arm,psci-suspend-param = <0x40000004>;
entry-latency-us = <800>;
exit-latency-us = <750>;
min-residency-us = <4090>;
local-timer-stop;
};
BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
compatible = "arm,idle-state";
idle-state-name = "gold-rail-power-collapse";
arm,psci-suspend-param = <0x40000004>;
entry-latency-us = <600>;
exit-latency-us = <1550>;
min-residency-us = <4791>;
local-timer-stop;
};
};
domain-idle-states {
CLUSTER_SLEEP_0: cluster-sleep-0 {
compatible = "domain-idle-state";
idle-state-name = "cluster-l3-off";
arm,psci-suspend-param = <0x41000044>;
entry-latency-us = <1050>;
exit-latency-us = <2500>;
min-residency-us = <5309>;
local-timer-stop;
};
CLUSTER_SLEEP_1: cluster-sleep-1 {
compatible = "domain-idle-state";
idle-state-name = "cluster-power-collapse";
arm,psci-suspend-param = <0x4100c344>;
entry-latency-us = <2700>;
exit-latency-us = <3500>;
min-residency-us = <13959>;
local-timer-stop;
};
};
};
firmware {
scm: scm {
compatible = "qcom,scm-sm8450", "qcom,scm";
interconnects = <&aggre2_noc MASTER_CRYPTO 0 &mc_virt SLAVE_EBI1 0>;
#reset-cells = <1>;
};
};
clk_virt: interconnect-0 {
compatible = "qcom,sm8450-clk-virt";
#interconnect-cells = <2>;
qcom,bcm-voters = <&apps_bcm_voter>;
};
mc_virt: interconnect-1 {
compatible = "qcom,sm8450-mc-virt";
#interconnect-cells = <2>;
qcom,bcm-voters = <&apps_bcm_voter>;
};
memory@a0000000 {
device_type = "memory";
/* We expect the bootloader to fill in the size */
reg = <0x0 0xa0000000 0x0 0x0>;
};
pmu {
compatible = "arm,armv8-pmuv3";
interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
};
psci {
compatible = "arm,psci-1.0";
method = "smc";
CPU_PD0: cpu0 {
#power-domain-cells = <0>;
power-domains = <&CLUSTER_PD>;
domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
};
CPU_PD1: cpu1 {
#power-domain-cells = <0>;
power-domains = <&CLUSTER_PD>;
domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
};
CPU_PD2: cpu2 {
#power-domain-cells = <0>;
power-domains = <&CLUSTER_PD>;
domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
};
CPU_PD3: cpu3 {
#power-domain-cells = <0>;
power-domains = <&CLUSTER_PD>;
domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
};
CPU_PD4: cpu4 {
#power-domain-cells = <0>;
power-domains = <&CLUSTER_PD>;
domain-idle-states = <&BIG_CPU_SLEEP_0>;
};
CPU_PD5: cpu5 {
#power-domain-cells = <0>;
power-domains = <&CLUSTER_PD>;
domain-idle-states = <&BIG_CPU_SLEEP_0>;
};
CPU_PD6: cpu6 {
#power-domain-cells = <0>;
power-domains = <&CLUSTER_PD>;
domain-idle-states = <&BIG_CPU_SLEEP_0>;
};
CPU_PD7: cpu7 {
#power-domain-cells = <0>;
power-domains = <&CLUSTER_PD>;
domain-idle-states = <&BIG_CPU_SLEEP_0>;
};
CLUSTER_PD: cpu-cluster0 {
#power-domain-cells = <0>;
domain-idle-states = <&CLUSTER_SLEEP_0>, <&CLUSTER_SLEEP_1>;
};
};
qup_opp_table_100mhz: opp-table-qup {
compatible = "operating-points-v2";
opp-50000000 {
opp-hz = /bits/ 64 <50000000>;
required-opps = <&rpmhpd_opp_min_svs>;
};
opp-75000000 {
opp-hz = /bits/ 64 <75000000>;
required-opps = <&rpmhpd_opp_low_svs>;
};
opp-100000000 {
opp-hz = /bits/ 64 <100000000>;
required-opps = <&rpmhpd_opp_svs>;
};
};
reserved_memory: reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
ranges;
hyp_mem: memory@80000000 {
reg = <0x0 0x80000000 0x0 0x600000>;
no-map;
};
xbl_dt_log_mem: memory@80600000 {
reg = <0x0 0x80600000 0x0 0x40000>;
no-map;
};
xbl_ramdump_mem: memory@80640000 {
reg = <0x0 0x80640000 0x0 0x180000>;
no-map;
};
xbl_sc_mem: memory@807c0000 {
reg = <0x0 0x807c0000 0x0 0x40000>;
no-map;
};
aop_image_mem: memory@80800000 {
reg = <0x0 0x80800000 0x0 0x60000>;
no-map;
};
aop_cmd_db_mem: memory@80860000 {
compatible = "qcom,cmd-db";
reg = <0x0 0x80860000 0x0 0x20000>;
no-map;
};
aop_config_mem: memory@80880000 {
reg = <0x0 0x80880000 0x0 0x20000>;
no-map;
};
tme_crash_dump_mem: memory@808a0000 {
reg = <0x0 0x808a0000 0x0 0x40000>;
no-map;
};
tme_log_mem: memory@808e0000 {
reg = <0x0 0x808e0000 0x0 0x4000>;
no-map;
};
uefi_log_mem: memory@808e4000 {
reg = <0x0 0x808e4000 0x0 0x10000>;
no-map;
};
/* secdata region can be reused by apps */
smem: memory@80900000 {
compatible = "qcom,smem";
reg = <0x0 0x80900000 0x0 0x200000>;
hwlocks = <&tcsr_mutex 3>;
no-map;
};
cpucp_fw_mem: memory@80b00000 {
reg = <0x0 0x80b00000 0x0 0x100000>;
no-map;
};
cdsp_secure_heap: memory@80c00000 {
reg = <0x0 0x80c00000 0x0 0x4600000>;
no-map;
};
video_mem: memory@85700000 {
reg = <0x0 0x85700000 0x0 0x700000>;
no-map;
};
adsp_mem: memory@85e00000 {
reg = <0x0 0x85e00000 0x0 0x2100000>;
no-map;
};
slpi_mem: memory@88000000 {
reg = <0x0 0x88000000 0x0 0x1900000>;
no-map;
};
cdsp_mem: memory@89900000 {
reg = <0x0 0x89900000 0x0 0x2000000>;
no-map;
};
ipa_fw_mem: memory@8b900000 {
reg = <0x0 0x8b900000 0x0 0x10000>;
no-map;
};
ipa_gsi_mem: memory@8b910000 {
reg = <0x0 0x8b910000 0x0 0xa000>;
no-map;
};
gpu_micro_code_mem: memory@8b91a000 {
reg = <0x0 0x8b91a000 0x0 0x2000>;
no-map;
};
spss_region_mem: memory@8ba00000 {
reg = <0x0 0x8ba00000 0x0 0x180000>;
no-map;
};
/* First part of the "SPU secure shared memory" region */
spu_tz_shared_mem: memory@8bb80000 {
reg = <0x0 0x8bb80000 0x0 0x60000>;
no-map;
};
/* Second part of the "SPU secure shared memory" region */
spu_modem_shared_mem: memory@8bbe0000 {
reg = <0x0 0x8bbe0000 0x0 0x20000>;
no-map;
};
mpss_mem: memory@8bc00000 {
reg = <0x0 0x8bc00000 0x0 0x13200000>;
no-map;
};
cvp_mem: memory@9ee00000 {
reg = <0x0 0x9ee00000 0x0 0x700000>;
no-map;
};
camera_mem: memory@9f500000 {
reg = <0x0 0x9f500000 0x0 0x800000>;
no-map;
};
rmtfs_mem: memory@9fd00000 {
compatible = "qcom,rmtfs-mem";
reg = <0x0 0x9fd00000 0x0 0x280000>;
no-map;
qcom,client-id = <1>;
qcom,vmid = <15>;
};
xbl_sc_mem2: memory@a6e00000 {
reg = <0x0 0xa6e00000 0x0 0x40000>;
no-map;
};
global_sync_mem: memory@a6f00000 {
reg = <0x0 0xa6f00000 0x0 0x100000>;
no-map;
};
/* uefi region can be reused by APPS */
/* Linux kernel image is loaded at 0xa0000000 */
oem_vm_mem: memory@bb000000 {
reg = <0x0 0xbb000000 0x0 0x5000000>;
no-map;
};
mte_mem: memory@c0000000 {
reg = <0x0 0xc0000000 0x0 0x20000000>;
no-map;
};
qheebsp_reserved_mem: memory@e0000000 {
reg = <0x0 0xe0000000 0x0 0x600000>;
no-map;
};
cpusys_vm_mem: memory@e0600000 {
reg = <0x0 0xe0600000 0x0 0x400000>;
no-map;
};
hyp_reserved_mem: memory@e0a00000 {
reg = <0x0 0xe0a00000 0x0 0x100000>;
no-map;
};
trust_ui_vm_mem: memory@e0b00000 {
reg = <0x0 0xe0b00000 0x0 0x4af3000>;
no-map;
};
trust_ui_vm_qrtr: memory@e55f3000 {
reg = <0x0 0xe55f3000 0x0 0x9000>;
no-map;
};
trust_ui_vm_vblk0_ring: memory@e55fc000 {
reg = <0x0 0xe55fc000 0x0 0x4000>;
no-map;
};
trust_ui_vm_swiotlb: memory@e5600000 {
reg = <0x0 0xe5600000 0x0 0x100000>;
no-map;
};
tz_stat_mem: memory@e8800000 {
reg = <0x0 0xe8800000 0x0 0x100000>;
no-map;
};
tags_mem: memory@e8900000 {
reg = <0x0 0xe8900000 0x0 0x1200000>;
no-map;
};
qtee_mem: memory@e9b00000 {
reg = <0x0 0xe9b00000 0x0 0x500000>;
no-map;
};
trusted_apps_mem: memory@ea000000 {
reg = <0x0 0xea000000 0x0 0x3900000>;
no-map;
};
trusted_apps_ext_mem: memory@ed900000 {
reg = <0x0 0xed900000 0x0 0x3b00000>;
no-map;
};
};
smp2p-adsp {
compatible = "qcom,smp2p";
qcom,smem = <443>, <429>;
interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
IPCC_MPROC_SIGNAL_SMP2P
IRQ_TYPE_EDGE_RISING>;
mboxes = <&ipcc IPCC_CLIENT_LPASS
IPCC_MPROC_SIGNAL_SMP2P>;
qcom,local-pid = <0>;
qcom,remote-pid = <2>;
smp2p_adsp_out: master-kernel {
qcom,entry-name = "master-kernel";
#qcom,smem-state-cells = <1>;
};
smp2p_adsp_in: slave-kernel {
qcom,entry-name = "slave-kernel";
interrupt-controller;
#interrupt-cells = <2>;
};
};
smp2p-cdsp {
compatible = "qcom,smp2p";
qcom,smem = <94>, <432>;
interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
IPCC_MPROC_SIGNAL_SMP2P
IRQ_TYPE_EDGE_RISING>;
mboxes = <&ipcc IPCC_CLIENT_CDSP
IPCC_MPROC_SIGNAL_SMP2P>;
qcom,local-pid = <0>;
qcom,remote-pid = <5>;
smp2p_cdsp_out: master-kernel {
qcom,entry-name = "master-kernel";
#qcom,smem-state-cells = <1>;
};
smp2p_cdsp_in: slave-kernel {
qcom,entry-name = "slave-kernel";
interrupt-controller;
#interrupt-cells = <2>;
};
};
smp2p-modem {
compatible = "qcom,smp2p";
qcom,smem = <435>, <428>;
interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
IPCC_MPROC_SIGNAL_SMP2P
IRQ_TYPE_EDGE_RISING>;
mboxes = <&ipcc IPCC_CLIENT_MPSS
IPCC_MPROC_SIGNAL_SMP2P>;
qcom,local-pid = <0>;
qcom,remote-pid = <1>;
smp2p_modem_out: master-kernel {
qcom,entry-name = "master-kernel";
#qcom,smem-state-cells = <1>;
};
smp2p_modem_in: slave-kernel {
qcom,entry-name = "slave-kernel";
interrupt-controller;
#interrupt-cells = <2>;
};
ipa_smp2p_out: ipa-ap-to-modem {
qcom,entry-name = "ipa";
#qcom,smem-state-cells = <1>;
};
ipa_smp2p_in: ipa-modem-to-ap {
qcom,entry-name = "ipa";
interrupt-controller;
#interrupt-cells = <2>;
};
};
smp2p-slpi {
compatible = "qcom,smp2p";
qcom,smem = <481>, <430>;
interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
IPCC_MPROC_SIGNAL_SMP2P
IRQ_TYPE_EDGE_RISING>;
mboxes = <&ipcc IPCC_CLIENT_SLPI
IPCC_MPROC_SIGNAL_SMP2P>;
qcom,local-pid = <0>;
qcom,remote-pid = <3>;
smp2p_slpi_out: master-kernel {
qcom,entry-name = "master-kernel";
#qcom,smem-state-cells = <1>;
};
smp2p_slpi_in: slave-kernel {
qcom,entry-name = "slave-kernel";
interrupt-controller;
#interrupt-cells = <2>;
};
};
soc: soc@0 {
#address-cells = <2>;
#size-cells = <2>;
ranges = <0 0 0 0 0x10 0>;
dma-ranges = <0 0 0 0 0x10 0>;
compatible = "simple-bus";
gcc: clock-controller@100000 {
compatible = "qcom,gcc-sm8450";
reg = <0x0 0x00100000 0x0 0x1f4200>;
#clock-cells = <1>;
#reset-cells = <1>;
#power-domain-cells = <1>;
clocks = <&rpmhcc RPMH_CXO_CLK>,
<&pcie0_lane>,
<&pcie1_lane>,
<&sleep_clk>;
clock-names = "bi_tcxo",
"pcie_0_pipe_clk",
"pcie_1_pipe_clk",
"sleep_clk";
};
gpi_dma2: dma-controller@800000 {
compatible = "qcom,sm8450-gpi-dma";
#dma-cells = <3>;
reg = <0 0x800000 0 0x60000>;
interrupts = <GIC_SPI 588 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 589 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 590 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 591 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 592 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 593 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 594 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 595 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 596 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 597 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 598 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 599 IRQ_TYPE_LEVEL_HIGH>;
dma-channels = <12>;
dma-channel-mask = <0x7e>;
iommus = <&apps_smmu 0x496 0x0>;
status = "disabled";
};
qupv3_id_2: geniqup@8c0000 {
compatible = "qcom,geni-se-qup";
reg = <0x0 0x008c0000 0x0 0x2000>;
clock-names = "m-ahb", "s-ahb";
clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>,
<&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>;
iommus = <&apps_smmu 0x483 0x0>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
status = "disabled";
i2c15: i2c@880000 {
compatible = "qcom,geni-i2c";
reg = <0x0 0x00880000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c15_data_clk>;
interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma2 0 0 QCOM_GPI_I2C>,
<&gpi_dma2 1 0 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
status = "disabled";
};
spi15: spi@880000 {
compatible = "qcom,geni-spi";
reg = <0x0 0x00880000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi15_data_clk>, <&qup_spi15_cs>;
spi-max-frequency = <50000000>;
interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
interconnect-names = "qup-core", "qup-config";
dmas = <&gpi_dma2 0 0 QCOM_GPI_SPI>,
<&gpi_dma2 1 0 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c16: i2c@884000 {
compatible = "qcom,geni-i2c";
reg = <0x0 0x00884000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c16_data_clk>;
interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma2 0 1 QCOM_GPI_I2C>,
<&gpi_dma2 1 1 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
status = "disabled";
};
spi16: spi@884000 {
compatible = "qcom,geni-spi";
reg = <0x0 0x00884000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi16_data_clk>, <&qup_spi16_cs>;
spi-max-frequency = <50000000>;
interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
interconnect-names = "qup-core", "qup-config";
dmas = <&gpi_dma2 0 1 QCOM_GPI_SPI>,
<&gpi_dma2 1 1 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c17: i2c@888000 {
compatible = "qcom,geni-i2c";
reg = <0x0 0x00888000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c17_data_clk>;
interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma2 0 2 QCOM_GPI_I2C>,
<&gpi_dma2 1 2 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
status = "disabled";
};
spi17: spi@888000 {
compatible = "qcom,geni-spi";
reg = <0x0 0x00888000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi17_data_clk>, <&qup_spi17_cs>;
spi-max-frequency = <50000000>;
interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
interconnect-names = "qup-core", "qup-config";
dmas = <&gpi_dma2 0 2 QCOM_GPI_SPI>,
<&gpi_dma2 1 2 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c18: i2c@88c000 {
compatible = "qcom,geni-i2c";
reg = <0x0 0x0088c000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c18_data_clk>;
interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>,
<&gpi_dma2 1 3 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
status = "disabled";
};
spi18: spi@88c000 {
compatible = "qcom,geni-spi";
reg = <0 0x0088c000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi18_data_clk>, <&qup_spi18_cs>;
spi-max-frequency = <50000000>;
interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
interconnect-names = "qup-core", "qup-config";
dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>,
<&gpi_dma2 1 3 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c19: i2c@890000 {
compatible = "qcom,geni-i2c";
reg = <0x0 0x00890000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c19_data_clk>;
interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma2 0 4 QCOM_GPI_I2C>,
<&gpi_dma2 1 4 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
status = "disabled";
};
spi19: spi@890000 {
compatible = "qcom,geni-spi";
reg = <0 0x00890000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi19_data_clk>, <&qup_spi19_cs>;
spi-max-frequency = <50000000>;
interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
interconnect-names = "qup-core", "qup-config";
dmas = <&gpi_dma2 0 4 QCOM_GPI_I2C>,
<&gpi_dma2 1 4 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c20: i2c@894000 {
compatible = "qcom,geni-i2c";
reg = <0x0 0x00894000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c20_data_clk>;
interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma2 0 5 QCOM_GPI_I2C>,
<&gpi_dma2 1 5 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
status = "disabled";
};
uart20: serial@894000 {
compatible = "qcom,geni-uart";
reg = <0 0x00894000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_uart20_default>;
interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi20: spi@894000 {
compatible = "qcom,geni-spi";
reg = <0 0x00894000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi20_data_clk>, <&qup_spi20_cs>;
spi-max-frequency = <50000000>;
interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
interconnect-names = "qup-core", "qup-config";
dmas = <&gpi_dma2 0 5 QCOM_GPI_SPI>,
<&gpi_dma2 1 5 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c21: i2c@898000 {
compatible = "qcom,geni-i2c";
reg = <0x0 0x00898000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S6_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c21_data_clk>;
interrupts = <GIC_SPI 579 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma2 0 6 QCOM_GPI_I2C>,
<&gpi_dma2 1 6 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
status = "disabled";
};
spi21: spi@898000 {
compatible = "qcom,geni-spi";
reg = <0 0x00898000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S6_CLK>;
interrupts = <GIC_SPI 579 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi21_data_clk>, <&qup_spi21_cs>;
spi-max-frequency = <50000000>;
interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
interconnect-names = "qup-core", "qup-config";
dmas = <&gpi_dma2 0 6 QCOM_GPI_SPI>,
<&gpi_dma2 1 6 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
};
gpi_dma0: dma-controller@900000 {
compatible = "qcom,sm8450-gpi-dma";
#dma-cells = <3>;
reg = <0 0x900000 0 0x60000>;
interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
dma-channels = <12>;
dma-channel-mask = <0x7e>;
iommus = <&apps_smmu 0x5b6 0x0>;
status = "disabled";
};
qupv3_id_0: geniqup@9c0000 {
compatible = "qcom,geni-se-qup";
reg = <0x0 0x009c0000 0x0 0x2000>;
clock-names = "m-ahb", "s-ahb";
clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
<&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
iommus = <&apps_smmu 0x5a3 0x0>;
interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>;
interconnect-names = "qup-core";
#address-cells = <2>;
#size-cells = <2>;
ranges;
status = "disabled";
i2c0: i2c@980000 {
compatible = "qcom,geni-i2c";
reg = <0x0 0x00980000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c0_data_clk>;
interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
<&gpi_dma0 1 0 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
status = "disabled";
};
spi0: spi@980000 {
compatible = "qcom,geni-spi";
reg = <0x0 0x00980000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>;
power-domains = <&rpmhpd SM8450_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
<&gpi_dma0 1 0 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c1: i2c@984000 {
compatible = "qcom,geni-i2c";
reg = <0x0 0x00984000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c1_data_clk>;
interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
<&gpi_dma0 1 1 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
status = "disabled";
};
spi1: spi@984000 {
compatible = "qcom,geni-spi";
reg = <0x0 0x00984000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>;
interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
<&gpi_dma0 1 1 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c2: i2c@988000 {
compatible = "qcom,geni-i2c";
reg = <0x0 0x00988000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c2_data_clk>;
interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
<&gpi_dma0 1 2 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
status = "disabled";
};
spi2: spi@988000 {
compatible = "qcom,geni-spi";
reg = <0x0 0x00988000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>;
interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
<&gpi_dma0 1 2 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c3: i2c@98c000 {
compatible = "qcom,geni-i2c";
reg = <0x0 0x0098c000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c3_data_clk>;
interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
<&gpi_dma0 1 3 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
status = "disabled";
};
spi3: spi@98c000 {
compatible = "qcom,geni-spi";
reg = <0x0 0x0098c000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>;
interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
<&gpi_dma0 1 3 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c4: i2c@990000 {
compatible = "qcom,geni-i2c";
reg = <0x0 0x00990000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c4_data_clk>;
interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
<&gpi_dma0 1 4 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
status = "disabled";
};
spi4: spi@990000 {
compatible = "qcom,geni-spi";
reg = <0x0 0x00990000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>;
power-domains = <&rpmhpd SM8450_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
<&gpi_dma0 1 4 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c5: i2c@994000 {
compatible = "qcom,geni-i2c";
reg = <0x0 0x00994000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c5_data_clk>;
interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
<&gpi_dma0 1 5 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
status = "disabled";
};
spi5: spi@994000 {
compatible = "qcom,geni-spi";
reg = <0x0 0x00994000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>;
interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
<&gpi_dma0 1 5 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c6: i2c@998000 {
compatible = "qcom,geni-i2c";
reg = <0x0 0x998000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c6_data_clk>;
interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 6 QCOM_GPI_I2C>,
<&gpi_dma0 1 6 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
status = "disabled";
};
spi6: spi@998000 {
compatible = "qcom,geni-spi";
reg = <0x0 0x998000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>;
interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 6 QCOM_GPI_SPI>,
<&gpi_dma0 1 6 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
uart7: serial@99c000 {
compatible = "qcom,geni-debug-uart";
reg = <0 0x0099c000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_uart7_tx>, <&qup_uart7_rx>;
interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
};
gpi_dma1: dma-controller@a00000 {
compatible = "qcom,sm8450-gpi-dma";
#dma-cells = <3>;
reg = <0 0xa00000 0 0x60000>;
interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
dma-channels = <12>;
dma-channel-mask = <0x7e>;
iommus = <&apps_smmu 0x56 0x0>;
status = "disabled";
};
qupv3_id_1: geniqup@ac0000 {
compatible = "qcom,geni-se-qup";
reg = <0x0 0x00ac0000 0x0 0x6000>;
clock-names = "m-ahb", "s-ahb";
clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
<&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
iommus = <&apps_smmu 0x43 0x0>;
interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>;
interconnect-names = "qup-core";
#address-cells = <2>;
#size-cells = <2>;
ranges;
status = "disabled";
i2c8: i2c@a80000 {
compatible = "qcom,geni-i2c";
reg = <0x0 0x00a80000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c8_data_clk>;
interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
<&gpi_dma1 1 0 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
status = "disabled";
};
spi8: spi@a80000 {
compatible = "qcom,geni-spi";
reg = <0x0 0x00a80000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs>;
interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>,
<&gpi_dma1 1 0 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c9: i2c@a84000 {
compatible = "qcom,geni-i2c";
reg = <0x0 0x00a84000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c9_data_clk>;
interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
<&gpi_dma1 1 1 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
status = "disabled";
};
spi9: spi@a84000 {
compatible = "qcom,geni-spi";
reg = <0x0 0x00a84000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>;
interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>,
<&gpi_dma1 1 1 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c10: i2c@a88000 {
compatible = "qcom,geni-i2c";
reg = <0x0 0x00a88000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c10_data_clk>;
interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
<&gpi_dma1 1 2 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
status = "disabled";
};
spi10: spi@a88000 {
compatible = "qcom,geni-spi";
reg = <0x0 0x00a88000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>;
interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>,
<&gpi_dma1 1 2 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c11: i2c@a8c000 {
compatible = "qcom,geni-i2c";
reg = <0x0 0x00a8c000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c11_data_clk>;
interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
<&gpi_dma1 1 3 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
status = "disabled";
};
spi11: spi@a8c000 {
compatible = "qcom,geni-spi";
reg = <0x0 0x00a8c000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi11_data_clk>, <&qup_spi11_cs>;
interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>,
<&gpi_dma1 1 3 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c12: i2c@a90000 {
compatible = "qcom,geni-i2c";
reg = <0x0 0x00a90000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c12_data_clk>;
interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
<&gpi_dma1 1 4 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
status = "disabled";
};
spi12: spi@a90000 {
compatible = "qcom,geni-spi";
reg = <0x0 0x00a90000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi12_data_clk>, <&qup_spi12_cs>;
interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>,
<&gpi_dma1 1 4 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c13: i2c@a94000 {
compatible = "qcom,geni-i2c";
reg = <0 0x00a94000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c13_data_clk>;
interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>,
<&gpi_dma1 1 5 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi13: spi@a94000 {
compatible = "qcom,geni-spi";
reg = <0x0 0x00a94000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi13_data_clk>, <&qup_spi13_cs>;
interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 5 QCOM_GPI_SPI>,
<&gpi_dma1 1 5 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c14: i2c@a98000 {
compatible = "qcom,geni-i2c";
reg = <0 0x00a98000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c14_data_clk>;
interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 6 QCOM_GPI_I2C>,
<&gpi_dma1 1 6 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi14: spi@a98000 {
compatible = "qcom,geni-spi";
reg = <0x0 0x00a98000 0x0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&qup_spi14_data_clk>, <&qup_spi14_cs>;
interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 6 QCOM_GPI_SPI>,
<&gpi_dma1 1 6 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
};
pcie0: pci@1c00000 {
compatible = "qcom,pcie-sm8450-pcie0";
reg = <0 0x01c00000 0 0x3000>,
<0 0x60000000 0 0xf1d>,
<0 0x60000f20 0 0xa8>,
<0 0x60001000 0 0x1000>,
<0 0x60100000 0 0x100000>;
reg-names = "parf", "dbi", "elbi", "atu", "config";
device_type = "pci";
linux,pci-domain = <0>;
bus-range = <0x00 0xff>;
num-lanes = <1>;
#address-cells = <3>;
#size-cells = <2>;
ranges = <0x01000000 0x0 0x60200000 0 0x60200000 0x0 0x100000>,
<0x02000000 0x0 0x60300000 0 0x60300000 0x0 0x3d00000>;
interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
interrupt-map = <0 0 0 1 &intc 0 0 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
<0 0 0 2 &intc 0 0 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
<0 0 0 3 &intc 0 0 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
<0 0 0 4 &intc 0 0 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
<&gcc GCC_PCIE_0_PIPE_CLK_SRC>,
<&pcie0_lane>,
<&rpmhcc RPMH_CXO_CLK>,
<&gcc GCC_PCIE_0_AUX_CLK>,
<&gcc GCC_PCIE_0_CFG_AHB_CLK>,
<&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
<&gcc GCC_PCIE_0_SLV_AXI_CLK>,
<&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
<&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
<&gcc GCC_AGGRE_NOC_PCIE_0_AXI_CLK>,
<&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>;
clock-names = "pipe",
"pipe_mux",
"phy_pipe",
"ref",
"aux",
"cfg",
"bus_master",
"bus_slave",
"slave_q2a",
"ddrss_sf_tbu",
"aggre0",
"aggre1";
iommus = <&apps_smmu 0x1c00 0x7f>;
iommu-map = <0x0 &apps_smmu 0x1c00 0x1>,
<0x100 &apps_smmu 0x1c01 0x1>;
resets = <&gcc GCC_PCIE_0_BCR>;
reset-names = "pci";
power-domains = <&gcc PCIE_0_GDSC>;
power-domain-names = "gdsc";
phys = <&pcie0_lane>;
phy-names = "pciephy";
perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pcie0_default_state>;
status = "disabled";
};
pcie0_phy: phy@1c06000 {
compatible = "qcom,sm8450-qmp-gen3x1-pcie-phy";
reg = <0 0x01c06000 0 0x200>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
<&gcc GCC_PCIE_0_CFG_AHB_CLK>,
<&gcc GCC_PCIE_0_CLKREF_EN>,
<&gcc GCC_PCIE_0_PHY_RCHNG_CLK>;
clock-names = "aux", "cfg_ahb", "ref", "refgen";
resets = <&gcc GCC_PCIE_0_PHY_BCR>;
reset-names = "phy";
assigned-clocks = <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>;
assigned-clock-rates = <100000000>;
status = "disabled";
pcie0_lane: phy@1c06200 {
reg = <0 0x1c06e00 0 0x200>, /* tx */
<0 0x1c07000 0 0x200>, /* rx */
<0 0x1c06200 0 0x200>, /* pcs */
<0 0x1c06600 0 0x200>; /* pcs_pcie */
clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
clock-names = "pipe0";
#clock-cells = <0>;
#phy-cells = <0>;
clock-output-names = "pcie_0_pipe_clk";
};
};
pcie1: pci@1c08000 {
compatible = "qcom,pcie-sm8450-pcie1";
reg = <0 0x01c08000 0 0x3000>,
<0 0x40000000 0 0xf1d>,
<0 0x40000f20 0 0xa8>,
<0 0x40001000 0 0x1000>,
<0 0x40100000 0 0x100000>;
reg-names = "parf", "dbi", "elbi", "atu", "config";
device_type = "pci";
linux,pci-domain = <1>;
bus-range = <0x00 0xff>;
num-lanes = <2>;
#address-cells = <3>;
#size-cells = <2>;
ranges = <0x01000000 0x0 0x40200000 0 0x40200000 0x0 0x100000>,
<0x02000000 0x0 0x40300000 0 0x40300000 0x0 0x1fd00000>;
interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
interrupt-map = <0 0 0 1 &intc 0 0 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
<0 0 0 2 &intc 0 0 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
<0 0 0 3 &intc 0 0 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
<0 0 0 4 &intc 0 0 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
<&gcc GCC_PCIE_1_PIPE_CLK_SRC>,
<&pcie1_lane>,
<&rpmhcc RPMH_CXO_CLK>,
<&gcc GCC_PCIE_1_AUX_CLK>,
<&gcc GCC_PCIE_1_CFG_AHB_CLK>,
<&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
<&gcc GCC_PCIE_1_SLV_AXI_CLK>,
<&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
<&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
<&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>;
clock-names = "pipe",
"pipe_mux",
"phy_pipe",
"ref",
"aux",
"cfg",
"bus_master",
"bus_slave",
"slave_q2a",
"ddrss_sf_tbu",
"aggre1";
iommus = <&apps_smmu 0x1c80 0x7f>;
iommu-map = <0x0 &apps_smmu 0x1c80 0x1>,
<0x100 &apps_smmu 0x1c81 0x1>;
resets = <&gcc GCC_PCIE_1_BCR>;
reset-names = "pci";
power-domains = <&gcc PCIE_1_GDSC>;
power-domain-names = "gdsc";
phys = <&pcie1_lane>;
phy-names = "pciephy";
perst-gpio = <&tlmm 97 GPIO_ACTIVE_LOW>;
enable-gpio = <&tlmm 99 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pcie1_default_state>;
status = "disabled";
};
pcie1_phy: phy@1c0f000 {
compatible = "qcom,sm8450-qmp-gen4x2-pcie-phy";
reg = <0 0x01c0f000 0 0x200>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
clocks = <&gcc GCC_PCIE_1_PHY_AUX_CLK>,
<&gcc GCC_PCIE_1_CFG_AHB_CLK>,
<&gcc GCC_PCIE_1_CLKREF_EN>,
<&gcc GCC_PCIE_1_PHY_RCHNG_CLK>;
clock-names = "aux", "cfg_ahb", "ref", "refgen";
resets = <&gcc GCC_PCIE_1_PHY_BCR>;
reset-names = "phy";
assigned-clocks = <&gcc GCC_PCIE_1_PHY_RCHNG_CLK>;
assigned-clock-rates = <100000000>;
status = "disabled";
pcie1_lane: phy@1c0e000 {
reg = <0 0x1c0e000 0 0x200>, /* tx */
<0 0x1c0e200 0 0x300>, /* rx */
<0 0x1c0f200 0 0x200>, /* pcs */
<0 0x1c0e800 0 0x200>, /* tx */
<0 0x1c0ea00 0 0x300>, /* rx */
<0 0x1c0f400 0 0xc00>; /* pcs_pcie */
clocks = <&gcc GCC_PCIE_1_PIPE_CLK>;
clock-names = "pipe0";
#clock-cells = <0>;
#phy-cells = <0>;
clock-output-names = "pcie_1_pipe_clk";
};
};
config_noc: interconnect@1500000 {
compatible = "qcom,sm8450-config-noc";
reg = <0 0x01500000 0 0x1c000>;
#interconnect-cells = <2>;
qcom,bcm-voters = <&apps_bcm_voter>;
};
system_noc: interconnect@1680000 {
compatible = "qcom,sm8450-system-noc";
reg = <0 0x01680000 0 0x1e200>;
#interconnect-cells = <2>;
qcom,bcm-voters = <&apps_bcm_voter>;
};
pcie_noc: interconnect@16c0000 {
compatible = "qcom,sm8450-pcie-anoc";
reg = <0 0x016c0000 0 0xe280>;
#interconnect-cells = <2>;
qcom,bcm-voters = <&apps_bcm_voter>;
};
aggre1_noc: interconnect@16e0000 {
compatible = "qcom,sm8450-aggre1-noc";
reg = <0 0x016e0000 0 0x1c080>;
#interconnect-cells = <2>;
clocks = <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
<&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>;
qcom,bcm-voters = <&apps_bcm_voter>;
};
aggre2_noc: interconnect@1700000 {
compatible = "qcom,sm8450-aggre2-noc";
reg = <0 0x01700000 0 0x31080>;
#interconnect-cells = <2>;
qcom,bcm-voters = <&apps_bcm_voter>;
clocks = <&gcc GCC_AGGRE_NOC_PCIE_0_AXI_CLK>,
<&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>,
<&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
<&rpmhcc RPMH_IPA_CLK>;
};
mmss_noc: interconnect@1740000 {
compatible = "qcom,sm8450-mmss-noc";
reg = <0 0x01740000 0 0x1f080>;
#interconnect-cells = <2>;
qcom,bcm-voters = <&apps_bcm_voter>;
};
tcsr_mutex: hwlock@1f40000 {
compatible = "qcom,tcsr-mutex";
reg = <0x0 0x01f40000 0x0 0x40000>;
#hwlock-cells = <1>;
};
usb_1_hsphy: phy@88e3000 {
compatible = "qcom,sm8450-usb-hs-phy",
"qcom,usb-snps-hs-7nm-phy";
reg = <0 0x088e3000 0 0x400>;
status = "disabled";
#phy-cells = <0>;
clocks = <&rpmhcc RPMH_CXO_CLK>;
clock-names = "ref";
resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
};
usb_1_qmpphy: phy-wrapper@88e9000 {
compatible = "qcom,sm8450-qmp-usb3-phy";
reg = <0 0x088e9000 0 0x200>,
<0 0x088e8000 0 0x20>;
status = "disabled";
#address-cells = <2>;
#size-cells = <2>;
ranges;
clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
<&rpmhcc RPMH_CXO_CLK>,
<&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
clock-names = "aux", "ref_clk_src", "com_aux";
resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
<&gcc GCC_USB3_PHY_PRIM_BCR>;
reset-names = "phy", "common";
usb_1_ssphy: phy@88e9200 {
reg = <0 0x088e9200 0 0x200>,
<0 0x088e9400 0 0x200>,
<0 0x088e9c00 0 0x400>,
<0 0x088e9600 0 0x200>,
<0 0x088e9800 0 0x200>,
<0 0x088e9a00 0 0x100>;
#phy-cells = <0>;
#clock-cells = <0>;
clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
clock-names = "pipe0";
clock-output-names = "usb3_phy_pipe_clk_src";
};
};
remoteproc_slpi: remoteproc@2400000 {
compatible = "qcom,sm8450-slpi-pas";
reg = <0 0x02400000 0 0x4000>;
interrupts-extended = <&pdc 9 IRQ_TYPE_EDGE_RISING>,
<&smp2p_slpi_in 0 IRQ_TYPE_EDGE_RISING>,
<&smp2p_slpi_in 1 IRQ_TYPE_EDGE_RISING>,
<&smp2p_slpi_in 2 IRQ_TYPE_EDGE_RISING>,
<&smp2p_slpi_in 3 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "wdog", "fatal", "ready",
"handover", "stop-ack";
clocks = <&rpmhcc RPMH_CXO_CLK>;
clock-names = "xo";
power-domains = <&rpmhpd SM8450_LCX>,
<&rpmhpd SM8450_LMX>;
power-domain-names = "lcx", "lmx";
memory-region = <&slpi_mem>;
qcom,qmp = <&aoss_qmp>;
qcom,smem-states = <&smp2p_slpi_out 0>;
qcom,smem-state-names = "stop";
status = "disabled";
glink-edge {
interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
IPCC_MPROC_SIGNAL_GLINK_QMP
IRQ_TYPE_EDGE_RISING>;
mboxes = <&ipcc IPCC_CLIENT_SLPI
IPCC_MPROC_SIGNAL_GLINK_QMP>;
label = "slpi";
qcom,remote-pid = <3>;
fastrpc {
compatible = "qcom,fastrpc";
qcom,glink-channels = "fastrpcglink-apps-dsp";
label = "sdsp";
#address-cells = <1>;
#size-cells = <0>;
compute-cb@1 {
compatible = "qcom,fastrpc-compute-cb";
reg = <1>;
iommus = <&apps_smmu 0x0541 0x0>;
};
compute-cb@2 {
compatible = "qcom,fastrpc-compute-cb";
reg = <2>;
iommus = <&apps_smmu 0x0542 0x0>;
};
compute-cb@3 {
compatible = "qcom,fastrpc-compute-cb";
reg = <3>;
iommus = <&apps_smmu 0x0543 0x0>;
/* note: shared-cb = <4> in downstream */
};
};
};
};
remoteproc_adsp: remoteproc@30000000 {
compatible = "qcom,sm8450-adsp-pas";
reg = <0 0x030000000 0 0x100>;
interrupts-extended = <&pdc 6 IRQ_TYPE_EDGE_RISING>,
<&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
<&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
<&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
<&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "wdog", "fatal", "ready",
"handover", "stop-ack";
clocks = <&rpmhcc RPMH_CXO_CLK>;
clock-names = "xo";
power-domains = <&rpmhpd SM8450_LCX>,
<&rpmhpd SM8450_LMX>;
power-domain-names = "lcx", "lmx";
memory-region = <&adsp_mem>;
qcom,qmp = <&aoss_qmp>;
qcom,smem-states = <&smp2p_adsp_out 0>;
qcom,smem-state-names = "stop";
status = "disabled";
remoteproc_adsp_glink: glink-edge {
interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
IPCC_MPROC_SIGNAL_GLINK_QMP
IRQ_TYPE_EDGE_RISING>;
mboxes = <&ipcc IPCC_CLIENT_LPASS
IPCC_MPROC_SIGNAL_GLINK_QMP>;
label = "lpass";
qcom,remote-pid = <2>;
fastrpc {
compatible = "qcom,fastrpc";
qcom,glink-channels = "fastrpcglink-apps-dsp";
label = "adsp";
#address-cells = <1>;
#size-cells = <0>;
compute-cb@3 {
compatible = "qcom,fastrpc-compute-cb";
reg = <3>;
iommus = <&apps_smmu 0x1803 0x0>;
};
compute-cb@4 {
compatible = "qcom,fastrpc-compute-cb";
reg = <4>;
iommus = <&apps_smmu 0x1804 0x0>;
};
compute-cb@5 {
compatible = "qcom,fastrpc-compute-cb";
reg = <5>;
iommus = <&apps_smmu 0x1805 0x0>;
};
};
};
};
remoteproc_cdsp: remoteproc@32300000 {
compatible = "qcom,sm8450-cdsp-pas";
reg = <0 0x032300000 0 0x1400000>;
interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>,
<&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>,
<&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>,
<&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>,
<&smp2p_cdsp_in 3 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "wdog", "fatal", "ready",
"handover", "stop-ack";
clocks = <&rpmhcc RPMH_CXO_CLK>;
clock-names = "xo";
power-domains = <&rpmhpd SM8450_CX>,
<&rpmhpd SM8450_MXC>;
power-domain-names = "cx", "mxc";
memory-region = <&cdsp_mem>;
qcom,qmp = <&aoss_qmp>;
qcom,smem-states = <&smp2p_cdsp_out 0>;
qcom,smem-state-names = "stop";
status = "disabled";
glink-edge {
interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
IPCC_MPROC_SIGNAL_GLINK_QMP
IRQ_TYPE_EDGE_RISING>;
mboxes = <&ipcc IPCC_CLIENT_CDSP
IPCC_MPROC_SIGNAL_GLINK_QMP>;
label = "cdsp";
qcom,remote-pid = <5>;
fastrpc {
compatible = "qcom,fastrpc";
qcom,glink-channels = "fastrpcglink-apps-dsp";
label = "cdsp";
#address-cells = <1>;
#size-cells = <0>;
compute-cb@1 {
compatible = "qcom,fastrpc-compute-cb";
reg = <1>;
iommus = <&apps_smmu 0x2161 0x0400>,
<&apps_smmu 0x1021 0x1420>;
};
compute-cb@2 {
compatible = "qcom,fastrpc-compute-cb";
reg = <2>;
iommus = <&apps_smmu 0x2162 0x0400>,
<&apps_smmu 0x1022 0x1420>;
};
compute-cb@3 {
compatible = "qcom,fastrpc-compute-cb";
reg = <3>;
iommus = <&apps_smmu 0x2163 0x0400>,
<&apps_smmu 0x1023 0x1420>;
};
compute-cb@4 {
compatible = "qcom,fastrpc-compute-cb";
reg = <4>;
iommus = <&apps_smmu 0x2164 0x0400>,
<&apps_smmu 0x1024 0x1420>;
};
compute-cb@5 {
compatible = "qcom,fastrpc-compute-cb";
reg = <5>;
iommus = <&apps_smmu 0x2165 0x0400>,
<&apps_smmu 0x1025 0x1420>;
};
compute-cb@6 {
compatible = "qcom,fastrpc-compute-cb";
reg = <6>;
iommus = <&apps_smmu 0x2166 0x0400>,
<&apps_smmu 0x1026 0x1420>;
};
compute-cb@7 {
compatible = "qcom,fastrpc-compute-cb";
reg = <7>;
iommus = <&apps_smmu 0x2167 0x0400>,
<&apps_smmu 0x1027 0x1420>;
};
compute-cb@8 {
compatible = "qcom,fastrpc-compute-cb";
reg = <8>;
iommus = <&apps_smmu 0x2168 0x0400>,
<&apps_smmu 0x1028 0x1420>;
};
/* note: secure cb9 in downstream */
};
};
};
remoteproc_mpss: remoteproc@4080000 {
compatible = "qcom,sm8450-mpss-pas";
reg = <0x0 0x04080000 0x0 0x4040>;
interrupts-extended = <&intc GIC_SPI 264 IRQ_TYPE_EDGE_RISING>,
<&smp2p_modem_in 0 IRQ_TYPE_EDGE_RISING>,
<&smp2p_modem_in 1 IRQ_TYPE_EDGE_RISING>,
<&smp2p_modem_in 2 IRQ_TYPE_EDGE_RISING>,
<&smp2p_modem_in 3 IRQ_TYPE_EDGE_RISING>,
<&smp2p_modem_in 7 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "wdog", "fatal", "ready", "handover",
"stop-ack", "shutdown-ack";
clocks = <&rpmhcc RPMH_CXO_CLK>;
clock-names = "xo";
power-domains = <&rpmhpd 0>,
<&rpmhpd 12>;
power-domain-names = "cx", "mss";
memory-region = <&mpss_mem>;
qcom,qmp = <&aoss_qmp>;
qcom,smem-states = <&smp2p_modem_out 0>;
qcom,smem-state-names = "stop";
status = "disabled";
glink-edge {
interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
IPCC_MPROC_SIGNAL_GLINK_QMP
IRQ_TYPE_EDGE_RISING>;
mboxes = <&ipcc IPCC_CLIENT_MPSS
IPCC_MPROC_SIGNAL_GLINK_QMP>;
label = "modem";
qcom,remote-pid = <1>;
};
};
camcc: clock-controller@ade0000 {
compatible = "qcom,sm8450-camcc";
reg = <0 0x0ade0000 0 0x20000>;
clocks = <&gcc GCC_CAMERA_AHB_CLK>,
<&rpmhcc RPMH_CXO_CLK>,
<&rpmhcc RPMH_CXO_CLK_A>,
<&sleep_clk>;
power-domains = <&rpmhpd SM8450_MMCX>;
required-opps = <&rpmhpd_opp_low_svs>;
#clock-cells = <1>;
#reset-cells = <1>;
#power-domain-cells = <1>;
status = "disabled";
};
pdc: interrupt-controller@b220000 {
compatible = "qcom,sm8450-pdc", "qcom,pdc";
reg = <0 0x0b220000 0 0x30000>, <0 0x174000f0 0 0x64>;
qcom,pdc-ranges = <0 480 12>, <14 494 24>, <40 520 54>,
<94 609 31>, <125 63 1>, <126 716 12>;
#interrupt-cells = <2>;
interrupt-parent = <&intc>;
interrupt-controller;
};
tsens0: thermal-sensor@c263000 {
compatible = "qcom,sm8450-tsens", "qcom,tsens-v2";
reg = <0 0x0c263000 0 0x1000>, /* TM */
<0 0x0c222000 0 0x1000>; /* SROT */
#qcom,sensors = <16>;
interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "uplow", "critical";
#thermal-sensor-cells = <1>;
};
tsens1: thermal-sensor@c265000 {
compatible = "qcom,sm8450-tsens", "qcom,tsens-v2";
reg = <0 0x0c265000 0 0x1000>, /* TM */
<0 0x0c223000 0 0x1000>; /* SROT */
#qcom,sensors = <16>;
interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "uplow", "critical";
#thermal-sensor-cells = <1>;
};
aoss_qmp: power-controller@c300000 {
compatible = "qcom,sm8450-aoss-qmp", "qcom,aoss-qmp";
reg = <0 0x0c300000 0 0x400>;
interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP
IRQ_TYPE_EDGE_RISING>;
mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>;
#clock-cells = <0>;
};
ipcc: mailbox@ed18000 {
compatible = "qcom,sm8450-ipcc", "qcom,ipcc";
reg = <0 0x0ed18000 0 0x1000>;
interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
interrupt-controller;
#interrupt-cells = <3>;
#mbox-cells = <2>;
};
tlmm: pinctrl@f100000 {
compatible = "qcom,sm8450-tlmm";
reg = <0 0x0f100000 0 0x300000>;
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
gpio-ranges = <&tlmm 0 0 211>;
wakeup-parent = <&pdc>;
sdc2_sleep_state: sdc2-sleep-state {
clk-pins {
pins = "sdc2_clk";
drive-strength = <2>;
bias-disable;
};
cmd-pins {
pins = "sdc2_cmd";
drive-strength = <2>;
bias-pull-up;
};
data-pins {
pins = "sdc2_data";
drive-strength = <2>;
bias-pull-up;
};
};
pcie0_default_state: pcie0-default-state {
perst-pins {
pins = "gpio94";
function = "gpio";
drive-strength = <2>;
bias-pull-down;
};
clkreq-pins {
pins = "gpio95";
function = "pcie0_clkreqn";
drive-strength = <2>;
bias-pull-up;
};
wake-pins {
pins = "gpio96";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
};
pcie1_default_state: pcie1-default-state {
perst-pins {
pins = "gpio97";
function = "gpio";
drive-strength = <2>;
bias-pull-down;
};
clkreq-pins {
pins = "gpio98";
function = "pcie1_clkreqn";
drive-strength = <2>;
bias-pull-up;
};
wake-pins {
pins = "gpio99";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
};
qup_i2c0_data_clk: qup-i2c0-data-clk-state {
pins = "gpio0", "gpio1";
function = "qup0";
};
qup_i2c1_data_clk: qup-i2c1-data-clk-state {
pins = "gpio4", "gpio5";
function = "qup1";
};
qup_i2c2_data_clk: qup-i2c2-data-clk-state {
pins = "gpio8", "gpio9";
function = "qup2";
};
qup_i2c3_data_clk: qup-i2c3-data-clk-state {
pins = "gpio12", "gpio13";
function = "qup3";
};
qup_i2c4_data_clk: qup-i2c4-data-clk-state {
pins = "gpio16", "gpio17";
function = "qup4";
};
qup_i2c5_data_clk: qup-i2c5-data-clk-state {
pins = "gpio206", "gpio207";
function = "qup5";
};
qup_i2c6_data_clk: qup-i2c6-data-clk-state {
pins = "gpio20", "gpio21";
function = "qup6";
};
qup_i2c8_data_clk: qup-i2c8-data-clk-state {
pins = "gpio28", "gpio29";
function = "qup8";
};
qup_i2c9_data_clk: qup-i2c9-data-clk-state {
pins = "gpio32", "gpio33";
function = "qup9";
};
qup_i2c10_data_clk: qup-i2c10-data-clk-state {
pins = "gpio36", "gpio37";
function = "qup10";
};
qup_i2c11_data_clk: qup-i2c11-data-clk-state {
pins = "gpio40", "gpio41";
function = "qup11";
};
qup_i2c12_data_clk: qup-i2c12-data-clk-state {
pins = "gpio44", "gpio45";
function = "qup12";
};
qup_i2c13_data_clk: qup-i2c13-data-clk-state {
pins = "gpio48", "gpio49";
function = "qup13";
drive-strength = <2>;
bias-pull-up;
};
qup_i2c14_data_clk: qup-i2c14-data-clk-state {
pins = "gpio52", "gpio53";
function = "qup14";
drive-strength = <2>;
bias-pull-up;
};
qup_i2c15_data_clk: qup-i2c15-data-clk-state {
pins = "gpio56", "gpio57";
function = "qup15";
};
qup_i2c16_data_clk: qup-i2c16-data-clk-state {
pins = "gpio60", "gpio61";
function = "qup16";
};
qup_i2c17_data_clk: qup-i2c17-data-clk-state {
pins = "gpio64", "gpio65";
function = "qup17";
};
qup_i2c18_data_clk: qup-i2c18-data-clk-state {
pins = "gpio68", "gpio69";
function = "qup18";
};
qup_i2c19_data_clk: qup-i2c19-data-clk-state {
pins = "gpio72", "gpio73";
function = "qup19";
};
qup_i2c20_data_clk: qup-i2c20-data-clk-state {
pins = "gpio76", "gpio77";
function = "qup20";
};
qup_i2c21_data_clk: qup-i2c21-data-clk-state {
pins = "gpio80", "gpio81";
function = "qup21";
};
qup_spi0_cs: qup-spi0-cs-state {
pins = "gpio3";
function = "qup0";
};
qup_spi0_data_clk: qup-spi0-data-clk-state {
pins = "gpio0", "gpio1", "gpio2";
function = "qup0";
};
qup_spi1_cs: qup-spi1-cs-state {
pins = "gpio7";
function = "qup1";
};
qup_spi1_data_clk: qup-spi1-data-clk-state {
pins = "gpio4", "gpio5", "gpio6";
function = "qup1";
};
qup_spi2_cs: qup-spi2-cs-state {
pins = "gpio11";
function = "qup2";
};
qup_spi2_data_clk: qup-spi2-data-clk-state {
pins = "gpio8", "gpio9", "gpio10";
function = "qup2";
};
qup_spi3_cs: qup-spi3-cs-state {
pins = "gpio15";
function = "qup3";
};
qup_spi3_data_clk: qup-spi3-data-clk-state {
pins = "gpio12", "gpio13", "gpio14";
function = "qup3";
};
qup_spi4_cs: qup-spi4-cs-state {
pins = "gpio19";
function = "qup4";
drive-strength = <6>;
bias-disable;
};
qup_spi4_data_clk: qup-spi4-data-clk-state {
pins = "gpio16", "gpio17", "gpio18";
function = "qup4";
};
qup_spi5_cs: qup-spi5-cs-state {
pins = "gpio85";
function = "qup5";
};
qup_spi5_data_clk: qup-spi5-data-clk-state {
pins = "gpio206", "gpio207", "gpio84";
function = "qup5";
};
qup_spi6_cs: qup-spi6-cs-state {
pins = "gpio23";
function = "qup6";
};
qup_spi6_data_clk: qup-spi6-data-clk-state {
pins = "gpio20", "gpio21", "gpio22";
function = "qup6";
};
qup_spi8_cs: qup-spi8-cs-state {
pins = "gpio31";
function = "qup8";
};
qup_spi8_data_clk: qup-spi8-data-clk-state {
pins = "gpio28", "gpio29", "gpio30";
function = "qup8";
};
qup_spi9_cs: qup-spi9-cs-state {
pins = "gpio35";
function = "qup9";
};
qup_spi9_data_clk: qup-spi9-data-clk-state {
pins = "gpio32", "gpio33", "gpio34";
function = "qup9";
};
qup_spi10_cs: qup-spi10-cs-state {
pins = "gpio39";
function = "qup10";
};
qup_spi10_data_clk: qup-spi10-data-clk-state {
pins = "gpio36", "gpio37", "gpio38";
function = "qup10";
};
qup_spi11_cs: qup-spi11-cs-state {
pins = "gpio43";
function = "qup11";
};
qup_spi11_data_clk: qup-spi11-data-clk-state {
pins = "gpio40", "gpio41", "gpio42";
function = "qup11";
};
qup_spi12_cs: qup-spi12-cs-state {
pins = "gpio47";
function = "qup12";
};
qup_spi12_data_clk: qup-spi12-data-clk-state {
pins = "gpio44", "gpio45", "gpio46";
function = "qup12";
};
qup_spi13_cs: qup-spi13-cs-state {
pins = "gpio51";
function = "qup13";
};
qup_spi13_data_clk: qup-spi13-data-clk-state {
pins = "gpio48", "gpio49", "gpio50";
function = "qup13";
};
qup_spi14_cs: qup-spi14-cs-state {
pins = "gpio55";
function = "qup14";
};
qup_spi14_data_clk: qup-spi14-data-clk-state {
pins = "gpio52", "gpio53", "gpio54";
function = "qup14";
};
qup_spi15_cs: qup-spi15-cs-state {
pins = "gpio59";
function = "qup15";
};
qup_spi15_data_clk: qup-spi15-data-clk-state {
pins = "gpio56", "gpio57", "gpio58";
function = "qup15";
};
qup_spi16_cs: qup-spi16-cs-state {
pins = "gpio63";
function = "qup16";
};
qup_spi16_data_clk: qup-spi16-data-clk-state {
pins = "gpio60", "gpio61", "gpio62";
function = "qup16";
};
qup_spi17_cs: qup-spi17-cs-state {
pins = "gpio67";
function = "qup17";
};
qup_spi17_data_clk: qup-spi17-data-clk-state {
pins = "gpio64", "gpio65", "gpio66";
function = "qup17";
};
qup_spi18_cs: qup-spi18-cs-state {
pins = "gpio71";
function = "qup18";
drive-strength = <6>;
bias-disable;
};
qup_spi18_data_clk: qup-spi18-data-clk-state {
pins = "gpio68", "gpio69", "gpio70";
function = "qup18";
drive-strength = <6>;
bias-disable;
};
qup_spi19_cs: qup-spi19-cs-state {
pins = "gpio75";
function = "qup19";
drive-strength = <6>;
bias-disable;
};
qup_spi19_data_clk: qup-spi19-data-clk-state {
pins = "gpio72", "gpio73", "gpio74";
function = "qup19";
drive-strength = <6>;
bias-disable;
};
qup_spi20_cs: qup-spi20-cs-state {
pins = "gpio79";
function = "qup20";
};
qup_spi20_data_clk: qup-spi20-data-clk-state {
pins = "gpio76", "gpio77", "gpio78";
function = "qup20";
};
qup_spi21_cs: qup-spi21-cs-state {
pins = "gpio83";
function = "qup21";
};
qup_spi21_data_clk: qup-spi21-data-clk-state {
pins = "gpio80", "gpio81", "gpio82";
function = "qup21";
};
qup_uart7_rx: qup-uart7-rx-state {
pins = "gpio26";
function = "qup7";
drive-strength = <2>;
bias-disable;
};
qup_uart7_tx: qup-uart7-tx-state {
pins = "gpio27";
function = "qup7";
drive-strength = <2>;
bias-disable;
};
qup_uart20_default: qup-uart20-default-state {
pins = "gpio76", "gpio77", "gpio78", "gpio79";
function = "qup20";
};
};
apps_smmu: iommu@15000000 {
compatible = "qcom,sm8450-smmu-500", "arm,mmu-500";
reg = <0 0x15000000 0 0x100000>;
#iommu-cells = <2>;
#global-interrupts = <1>;
interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 707 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 690 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 691 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 692 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 693 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 694 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 695 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 696 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 697 IRQ_TYPE_LEVEL_HIGH>;
};
intc: interrupt-controller@17100000 {
compatible = "arm,gic-v3";
#interrupt-cells = <3>;
interrupt-controller;
#redistributor-regions = <1>;
redistributor-stride = <0x0 0x40000>;
reg = <0x0 0x17100000 0x0 0x10000>, /* GICD */
<0x0 0x17180000 0x0 0x200000>; /* GICR * 8 */
interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
gic_its: msi-controller@17140000 {
compatible = "arm,gic-v3-its";
reg = <0x0 0x17140000 0x0 0x20000>;
msi-controller;
#msi-cells = <1>;
};
};
timer@17420000 {
compatible = "arm,armv7-timer-mem";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0 0 0x20000000>;
reg = <0x0 0x17420000 0x0 0x1000>;
clock-frequency = <19200000>;
frame@17421000 {
frame-number = <0>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x17421000 0x1000>,
<0x17422000 0x1000>;
};
frame@17423000 {
frame-number = <1>;
interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x17423000 0x1000>;
status = "disabled";
};
frame@17425000 {
frame-number = <2>;
interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x17425000 0x1000>;
status = "disabled";
};
frame@17427000 {
frame-number = <3>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x17427000 0x1000>;
status = "disabled";
};
frame@17429000 {
frame-number = <4>;
interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x17429000 0x1000>;
status = "disabled";
};
frame@1742b000 {
frame-number = <5>;
interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x1742b000 0x1000>;
status = "disabled";
};
frame@1742d000 {
frame-number = <6>;
interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x1742d000 0x1000>;
status = "disabled";
};
};
apps_rsc: rsc@17a00000 {
label = "apps_rsc";
compatible = "qcom,rpmh-rsc";
reg = <0x0 0x17a00000 0x0 0x10000>,
<0x0 0x17a10000 0x0 0x10000>,
<0x0 0x17a20000 0x0 0x10000>,
<0x0 0x17a30000 0x0 0x10000>;
reg-names = "drv-0", "drv-1", "drv-2", "drv-3";
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
qcom,tcs-offset = <0xd00>;
qcom,drv-id = <2>;
qcom,tcs-config = <ACTIVE_TCS 3>, <SLEEP_TCS 2>,
<WAKE_TCS 2>, <CONTROL_TCS 0>;
apps_bcm_voter: bcm-voter {
compatible = "qcom,bcm-voter";
};
rpmhcc: clock-controller {
compatible = "qcom,sm8450-rpmh-clk";
#clock-cells = <1>;
clock-names = "xo";
clocks = <&xo_board>;
};
rpmhpd: power-controller {
compatible = "qcom,sm8450-rpmhpd";
#power-domain-cells = <1>;
operating-points-v2 = <&rpmhpd_opp_table>;
rpmhpd_opp_table: opp-table {
compatible = "operating-points-v2";
rpmhpd_opp_ret: opp1 {
opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
};
rpmhpd_opp_min_svs: opp2 {
opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
};
rpmhpd_opp_low_svs: opp3 {
opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
};
rpmhpd_opp_svs: opp4 {
opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
};
rpmhpd_opp_svs_l1: opp5 {
opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
};
rpmhpd_opp_nom: opp6 {
opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
};
rpmhpd_opp_nom_l1: opp7 {
opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
};
rpmhpd_opp_nom_l2: opp8 {
opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
};
rpmhpd_opp_turbo: opp9 {
opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
};
rpmhpd_opp_turbo_l1: opp10 {
opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
};
};
};
};
cpufreq_hw: cpufreq@17d91000 {
compatible = "qcom,sm8450-cpufreq-epss", "qcom,cpufreq-epss";
reg = <0 0x17d91000 0 0x1000>,
<0 0x17d92000 0 0x1000>,
<0 0x17d93000 0 0x1000>;
reg-names = "freq-domain0", "freq-domain1", "freq-domain2";
clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
clock-names = "xo", "alternate";
interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "dcvsh-irq-0", "dcvsh-irq-1", "dcvsh-irq-2";
#freq-domain-cells = <1>;
};
gem_noc: interconnect@19100000 {
compatible = "qcom,sm8450-gem-noc";
reg = <0 0x19100000 0 0xbb800>;
#interconnect-cells = <2>;
qcom,bcm-voters = <&apps_bcm_voter>;
};
system-cache-controller@19200000 {
compatible = "qcom,sm8450-llcc";
reg = <0 0x19200000 0 0x580000>, <0 0x19a00000 0 0x80000>;
reg-names = "llcc_base", "llcc_broadcast_base";
interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
};
ufs_mem_hc: ufshc@1d84000 {
compatible = "qcom,sm8450-ufshc", "qcom,ufshc",
"jedec,ufs-2.0";
reg = <0 0x01d84000 0 0x3000>,
<0 0x01d88000 0 0x8000>;
reg-names = "std", "ice";
interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
phys = <&ufs_mem_phy_lanes>;
phy-names = "ufsphy";
lanes-per-direction = <2>;
#reset-cells = <1>;
resets = <&gcc GCC_UFS_PHY_BCR>;
reset-names = "rst";
power-domains = <&gcc UFS_PHY_GDSC>;
iommus = <&apps_smmu 0xe0 0x0>;
interconnects = <&aggre1_noc MASTER_UFS_MEM 0 &mc_virt SLAVE_EBI1 0>,
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_UFS_MEM_CFG 0>;
interconnect-names = "ufs-ddr", "cpu-ufs";
clock-names =
"core_clk",
"bus_aggr_clk",
"iface_clk",
"core_clk_unipro",
"ref_clk",
"tx_lane0_sync_clk",
"rx_lane0_sync_clk",
"rx_lane1_sync_clk",
"ice_core_clk";
clocks =
<&gcc GCC_UFS_PHY_AXI_CLK>,
<&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
<&gcc GCC_UFS_PHY_AHB_CLK>,
<&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
<&rpmhcc RPMH_CXO_CLK>,
<&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
<&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
<&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>,
<&gcc GCC_UFS_PHY_ICE_CORE_CLK>;
freq-table-hz =
<75000000 300000000>,
<0 0>,
<0 0>,
<75000000 300000000>,
<75000000 300000000>,
<0 0>,
<0 0>,
<0 0>,
<75000000 300000000>;
status = "disabled";
};
ufs_mem_phy: phy@1d87000 {
compatible = "qcom,sm8450-qmp-ufs-phy";
reg = <0 0x01d87000 0 0x1c4>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
clock-names = "ref", "ref_aux", "qref";
clocks = <&rpmhcc RPMH_CXO_CLK>,
<&gcc GCC_UFS_PHY_PHY_AUX_CLK>,
<&gcc GCC_UFS_0_CLKREF_EN>;
resets = <&ufs_mem_hc 0>;
reset-names = "ufsphy";
status = "disabled";
ufs_mem_phy_lanes: phy@1d87400 {
reg = <0 0x01d87400 0 0x108>,
<0 0x01d87600 0 0x1e0>,
<0 0x01d87c00 0 0x1dc>,
<0 0x01d87800 0 0x108>,
<0 0x01d87a00 0 0x1e0>;
#phy-cells = <0>;
};
};
sdhc_2: sdhci@8804000 {
compatible = "qcom,sm8450-sdhci", "qcom,sdhci-msm-v5";
reg = <0 0x08804000 0 0x1000>;
interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "hc_irq", "pwr_irq";
clocks = <&gcc GCC_SDCC2_AHB_CLK>,
<&gcc GCC_SDCC2_APPS_CLK>,
<&rpmhcc RPMH_CXO_CLK>;
clock-names = "iface", "core", "xo";
resets = <&gcc GCC_SDCC2_BCR>;
interconnects = <&aggre2_noc MASTER_SDCC_2 0 &mc_virt SLAVE_EBI1 0>,
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_SDCC_2 0>;
interconnect-names = "sdhc-ddr","cpu-sdhc";
iommus = <&apps_smmu 0x4a0 0x0>;
power-domains = <&rpmhpd SM8450_CX>;
operating-points-v2 = <&sdhc2_opp_table>;
bus-width = <4>;
dma-coherent;
status = "disabled";
sdhc2_opp_table: opp-table {
compatible = "operating-points-v2";
opp-100000000 {
opp-hz = /bits/ 64 <100000000>;
required-opps = <&rpmhpd_opp_low_svs>;
};
opp-202000000 {
opp-hz = /bits/ 64 <202000000>;
required-opps = <&rpmhpd_opp_svs_l1>;
};
};
};
usb_1: usb@a6f8800 {
compatible = "qcom,sm8450-dwc3", "qcom,dwc3";
reg = <0 0x0a6f8800 0 0x400>;
status = "disabled";
#address-cells = <2>;
#size-cells = <2>;
ranges;
clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
<&gcc GCC_USB30_PRIM_MASTER_CLK>,
<&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
<&gcc GCC_USB30_PRIM_SLEEP_CLK>,
<&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
<&gcc GCC_USB3_0_CLKREF_EN>;
clock-names = "cfg_noc",
"core",
"iface",
"sleep",
"mock_utmi",
"xo";
assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
<&gcc GCC_USB30_PRIM_MASTER_CLK>;
assigned-clock-rates = <19200000>, <200000000>;
interrupts-extended = <&intc GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
<&pdc 17 IRQ_TYPE_LEVEL_HIGH>,
<&pdc 15 IRQ_TYPE_EDGE_BOTH>,
<&pdc 14 IRQ_TYPE_EDGE_BOTH>;
interrupt-names = "hs_phy_irq",
"ss_phy_irq",
"dm_hs_phy_irq",
"dp_hs_phy_irq";
power-domains = <&gcc USB30_PRIM_GDSC>;
resets = <&gcc GCC_USB30_PRIM_BCR>;
usb_1_dwc3: usb@a600000 {
compatible = "snps,dwc3";
reg = <0 0x0a600000 0 0xcd00>;
interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
iommus = <&apps_smmu 0x0 0x0>;
snps,dis_u2_susphy_quirk;
snps,dis_enblslpm_quirk;
phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
phy-names = "usb2-phy", "usb3-phy";
};
};
nsp_noc: interconnect@320c0000 {
compatible = "qcom,sm8450-nsp-noc";
reg = <0 0x320c0000 0 0x10000>;
#interconnect-cells = <2>;
qcom,bcm-voters = <&apps_bcm_voter>;
};
lpass_ag_noc: interconnect@3c40000 {
compatible = "qcom,sm8450-lpass-ag-noc";
reg = <0 0x3c40000 0 0x17200>;
#interconnect-cells = <2>;
qcom,bcm-voters = <&apps_bcm_voter>;
};
};
thermal-zones {
aoss0-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens0 0>;
trips {
thermal-engine-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
reset-mon-cfg {
temperature = <115000>;
hysteresis = <5000>;
type = "passive";
};
};
};
cpuss0-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens0 1>;
trips {
thermal-engine-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
reset-mon-cfg {
temperature = <115000>;
hysteresis = <5000>;
type = "passive";
};
};
};
cpuss1-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens0 2>;
trips {
thermal-engine-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
reset-mon-cfg {
temperature = <115000>;
hysteresis = <5000>;
type = "passive";
};
};
};
cpuss3-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens0 3>;
trips {
thermal-engine-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
reset-mon-cfg {
temperature = <115000>;
hysteresis = <5000>;
type = "passive";
};
};
};
cpuss4-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens0 4>;
trips {
thermal-engine-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
reset-mon-cfg {
temperature = <115000>;
hysteresis = <5000>;
type = "passive";
};
};
};
cpu4-top-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens0 5>;
trips {
cpu4_top_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu4_top_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu4_top_crit: cpu_crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
};
cpu4-bottom-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens0 6>;
trips {
cpu4_bottom_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu4_bottom_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu4_bottom_crit: cpu_crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
};
cpu5-top-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens0 7>;
trips {
cpu5_top_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu5_top_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu5_top_crit: cpu_crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
};
cpu5-bottom-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens0 8>;
trips {
cpu5_bottom_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu5_bottom_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu5_bottom_crit: cpu_crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
};
cpu6-top-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens0 9>;
trips {
cpu6_top_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu6_top_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu6_top_crit: cpu_crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
};
cpu6-bottom-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens0 10>;
trips {
cpu6_bottom_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu6_bottom_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu6_bottom_crit: cpu_crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
};
cpu7-top-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens0 11>;
trips {
cpu7_top_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu7_top_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu7_top_crit: cpu_crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
};
cpu7-middle-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens0 12>;
trips {
cpu7_middle_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu7_middle_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu7_middle_crit: cpu_crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
};
cpu7-bottom-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens0 13>;
trips {
cpu7_bottom_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu7_bottom_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu7_bottom_crit: cpu_crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
};
gpu-top-thermal {
polling-delay-passive = <10>;
polling-delay = <0>;
thermal-sensors = <&tsens0 14>;
trips {
thermal-engine-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
thermal-hal-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
reset-mon-cfg {
temperature = <115000>;
hysteresis = <5000>;
type = "passive";
};
gpu0_tj_cfg: tj_cfg {
temperature = <95000>;
hysteresis = <5000>;
type = "passive";
};
};
};
gpu-bottom-thermal {
polling-delay-passive = <10>;
polling-delay = <0>;
thermal-sensors = <&tsens0 15>;
trips {
thermal-engine-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
thermal-hal-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
reset-mon-cfg {
temperature = <115000>;
hysteresis = <5000>;
type = "passive";
};
gpu1_tj_cfg: tj_cfg {
temperature = <95000>;
hysteresis = <5000>;
type = "passive";
};
};
};
aoss1-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens1 0>;
trips {
thermal-engine-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
reset-mon-cfg {
temperature = <115000>;
hysteresis = <5000>;
type = "passive";
};
};
};
cpu0-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens1 1>;
trips {
cpu0_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu0_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu0_crit: cpu_crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
};
cpu1-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens1 2>;
trips {
cpu1_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu1_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu1_crit: cpu_crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
};
cpu2-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens1 3>;
trips {
cpu2_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu2_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu2_crit: cpu_crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
};
cpu3-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens1 4>;
trips {
cpu3_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu3_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu3_crit: cpu_crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
};
cdsp0-thermal {
polling-delay-passive = <10>;
polling-delay = <0>;
thermal-sensors = <&tsens1 5>;
trips {
thermal-engine-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
thermal-hal-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
reset-mon-cfg {
temperature = <115000>;
hysteresis = <5000>;
type = "passive";
};
cdsp_0_config: junction-config {
temperature = <95000>;
hysteresis = <5000>;
type = "passive";
};
};
};
cdsp1-thermal {
polling-delay-passive = <10>;
polling-delay = <0>;
thermal-sensors = <&tsens1 6>;
trips {
thermal-engine-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
thermal-hal-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
reset-mon-cfg {
temperature = <115000>;
hysteresis = <5000>;
type = "passive";
};
cdsp_1_config: junction-config {
temperature = <95000>;
hysteresis = <5000>;
type = "passive";
};
};
};
cdsp2-thermal {
polling-delay-passive = <10>;
polling-delay = <0>;
thermal-sensors = <&tsens1 7>;
trips {
thermal-engine-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
thermal-hal-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
reset-mon-cfg {
temperature = <115000>;
hysteresis = <5000>;
type = "passive";
};
cdsp_2_config: junction-config {
temperature = <95000>;
hysteresis = <5000>;
type = "passive";
};
};
};
video-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens1 8>;
trips {
thermal-engine-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
reset-mon-cfg {
temperature = <115000>;
hysteresis = <5000>;
type = "passive";
};
};
};
mem-thermal {
polling-delay-passive = <10>;
polling-delay = <0>;
thermal-sensors = <&tsens1 9>;
trips {
thermal-engine-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
ddr_config0: ddr0-config {
temperature = <90000>;
hysteresis = <5000>;
type = "passive";
};
reset-mon-cfg {
temperature = <115000>;
hysteresis = <5000>;
type = "passive";
};
};
};
modem0-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens1 10>;
trips {
thermal-engine-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
mdmss0_config0: mdmss0-config0 {
temperature = <102000>;
hysteresis = <3000>;
type = "passive";
};
mdmss0_config1: mdmss0-config1 {
temperature = <105000>;
hysteresis = <3000>;
type = "passive";
};
reset-mon-cfg {
temperature = <115000>;
hysteresis = <5000>;
type = "passive";
};
};
};
modem1-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens1 11>;
trips {
thermal-engine-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
mdmss1_config0: mdmss1-config0 {
temperature = <102000>;
hysteresis = <3000>;
type = "passive";
};
mdmss1_config1: mdmss1-config1 {
temperature = <105000>;
hysteresis = <3000>;
type = "passive";
};
reset-mon-cfg {
temperature = <115000>;
hysteresis = <5000>;
type = "passive";
};
};
};
modem2-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens1 12>;
trips {
thermal-engine-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
mdmss2_config0: mdmss2-config0 {
temperature = <102000>;
hysteresis = <3000>;
type = "passive";
};
mdmss2_config1: mdmss2-config1 {
temperature = <105000>;
hysteresis = <3000>;
type = "passive";
};
reset-mon-cfg {
temperature = <115000>;
hysteresis = <5000>;
type = "passive";
};
};
};
modem3-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens1 13>;
trips {
thermal-engine-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
mdmss3_config0: mdmss3-config0 {
temperature = <102000>;
hysteresis = <3000>;
type = "passive";
};
mdmss3_config1: mdmss3-config1 {
temperature = <105000>;
hysteresis = <3000>;
type = "passive";
};
reset-mon-cfg {
temperature = <115000>;
hysteresis = <5000>;
type = "passive";
};
};
};
camera0-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens1 14>;
trips {
thermal-engine-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
reset-mon-cfg {
temperature = <115000>;
hysteresis = <5000>;
type = "passive";
};
};
};
camera1-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&tsens1 15>;
trips {
thermal-engine-config {
temperature = <125000>;
hysteresis = <1000>;
type = "passive";
};
reset-mon-cfg {
temperature = <115000>;
hysteresis = <5000>;
type = "passive";
};
};
};
};
timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
clock-frequency = <19200000>;
};
};
