Staging
v0.5.2
v0.5.2
https://github.com/torvalds/linux
Tip revision: e40152ee1e1c7a63f4777791863215e3faa37a86 authored by Linus Torvalds on 16 May 2010, 21:17:36 UTC
Linus 2.6.34
Linus 2.6.34
Tip revision: e40152e
Kconfig
if ARCH_OMAP
menu "TI OMAP Implementations"
config ARCH_OMAP_OTG
bool
choice
prompt "OMAP System Type"
default ARCH_OMAP2PLUS
config ARCH_OMAP1
bool "TI OMAP1"
select COMMON_CLKDEV
help
"Systems based on omap7xx, omap15xx or omap16xx"
config ARCH_OMAP2PLUS
bool "TI OMAP2/3/4"
select COMMON_CLKDEV
help
"Systems based on omap24xx, omap34xx or omap44xx"
config ARCH_OMAP2
bool "TI OMAP2"
depends on ARCH_OMAP2PLUS
select CPU_V6
config ARCH_OMAP3
bool "TI OMAP3"
depends on ARCH_OMAP2PLUS
select CPU_V7
select USB_ARCH_HAS_EHCI
select ARM_L1_CACHE_SHIFT_6
config ARCH_OMAP4
bool "TI OMAP4"
depends on ARCH_OMAP2PLUS
select CPU_V7
select ARM_GIC
endchoice
comment "OMAP Feature Selections"
config OMAP_DEBUG_DEVICES
bool
help
For debug cards on TI reference boards.
config OMAP_DEBUG_LEDS
bool
depends on OMAP_DEBUG_DEVICES
default y if LEDS || LEDS_OMAP_DEBUG
config OMAP_RESET_CLOCKS
bool "Reset unused clocks during boot"
depends on ARCH_OMAP
help
Say Y if you want to reset unused clocks during boot.
This option saves power, but assumes all drivers are
using the clock framework. Broken drivers that do not
yet use clock framework may not work with this option.
If you are booting from another operating system, you
probably do not want this option enabled until your
device drivers work properly.
config OMAP_MUX
bool "OMAP multiplexing support"
depends on ARCH_OMAP
default y
help
Pin multiplexing support for OMAP boards. If your bootloader
sets the multiplexing correctly, say N. Otherwise, or if unsure,
say Y.
config OMAP_MUX_DEBUG
bool "Multiplexing debug output"
depends on OMAP_MUX
help
Makes the multiplexing functions print out a lot of debug info.
This is useful if you want to find out the correct values of the
multiplexing registers.
config OMAP_MUX_WARNINGS
bool "Warn about pins the bootloader didn't set up"
depends on OMAP_MUX
default y
help
Choose Y here to warn whenever driver initialization logic needs
to change the pin multiplexing setup. When there are no warnings
printed, it's safe to deselect OMAP_MUX for your product.
config OMAP_MCBSP
bool "McBSP support"
depends on ARCH_OMAP
default y
help
Say Y here if you want support for the OMAP Multichannel
Buffered Serial Port.
config OMAP_MBOX_FWK
tristate "Mailbox framework support"
depends on ARCH_OMAP
help
Say Y here if you want to use OMAP Mailbox framework support for
DSP, IVA1.0 and IVA2 in OMAP1/2/3.
config OMAP_IOMMU
tristate
config OMAP_IOMMU_DEBUG
depends on OMAP_IOMMU
tristate
choice
prompt "System timer"
default OMAP_MPU_TIMER
config OMAP_MPU_TIMER
bool "Use mpu timer"
help
Select this option if you want to use the OMAP mpu timer. This
timer provides more intra-tick resolution than the 32KHz timer,
but consumes more power.
config OMAP_32K_TIMER
bool "Use 32KHz timer"
depends on ARCH_OMAP16XX || ARCH_OMAP2PLUS
help
Select this option if you want to enable the OMAP 32KHz timer.
This timer saves power compared to the OMAP_MPU_TIMER, and has
support for no tick during idle. The 32KHz timer provides less
intra-tick resolution than OMAP_MPU_TIMER. The 32KHz timer is
currently only available for OMAP16XX, 24XX, 34XX and OMAP4.
endchoice
config OMAP3_L2_AUX_SECURE_SAVE_RESTORE
bool "OMAP3 HS/EMU save and restore for L2 AUX control register"
depends on ARCH_OMAP3 && PM
default n
help
Without this option, L2 Auxiliary control register contents are
lost during off-mode entry on HS/EMU devices. This feature
requires support from PPA / boot-loader in HS/EMU devices, which
currently does not exist by default.
config OMAP3_L2_AUX_SECURE_SERVICE_SET_ID
int "Service ID for the support routine to set L2 AUX control"
depends on OMAP3_L2_AUX_SECURE_SAVE_RESTORE
default 43
help
PPA routine service ID for setting L2 auxiliary control register.
config OMAP_32K_TIMER_HZ
int "Kernel internal timer frequency for 32KHz timer"
range 32 1024
depends on OMAP_32K_TIMER
default "128"
help
Kernel internal timer frequency should be a divisor of 32768,
such as 64 or 128.
config OMAP_DM_TIMER
bool "Use dual-mode timer"
depends on ARCH_OMAP16XX || ARCH_OMAP2PLUS
help
Select this option if you want to use OMAP Dual-Mode timers.
config OMAP_SERIAL_WAKE
bool "Enable wake-up events for serial ports"
depends on ARCH_OMAP1 && OMAP_MUX
default y
help
Select this option if you want to have your system wake up
to data on the serial RX line. This allows you to wake the
system from serial console.
choice
prompt "OMAP PM layer selection"
depends on ARCH_OMAP
default OMAP_PM_NOOP
config OMAP_PM_NONE
bool "No PM layer"
config OMAP_PM_NOOP
bool "No-op/debug PM layer"
endchoice
endmenu
endif