Staging
v0.5.2
v0.5.2
https://github.com/torvalds/linux
Tip revision: 9489e9dcae718d5fde988e4a684a0f55b5f94d17 authored by Linus Torvalds on 26 November 2012, 01:59:19 UTC
Linux 3.7-rc7
Linux 3.7-rc7
Tip revision: 9489e9d
guruplug-setup.c
/*
* arch/arm/mach-kirkwood/guruplug-setup.c
*
* Marvell GuruPlug Reference Board Setup
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/mtd/partitions.h>
#include <linux/ata_platform.h>
#include <linux/mv643xx_eth.h>
#include <linux/gpio.h>
#include <linux/leds.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/kirkwood.h>
#include <linux/platform_data/mmc-mvsdio.h>
#include "common.h"
#include "mpp.h"
static struct mtd_partition guruplug_nand_parts[] = {
{
.name = "u-boot",
.offset = 0,
.size = SZ_1M
}, {
.name = "uImage",
.offset = MTDPART_OFS_NXTBLK,
.size = SZ_4M
}, {
.name = "root",
.offset = MTDPART_OFS_NXTBLK,
.size = MTDPART_SIZ_FULL
},
};
static struct mv643xx_eth_platform_data guruplug_ge00_data = {
.phy_addr = MV643XX_ETH_PHY_ADDR(0),
};
static struct mv643xx_eth_platform_data guruplug_ge01_data = {
.phy_addr = MV643XX_ETH_PHY_ADDR(1),
};
static struct mv_sata_platform_data guruplug_sata_data = {
.n_ports = 1,
};
static struct mvsdio_platform_data guruplug_mvsdio_data = {
/* unfortunately the CD signal has not been connected */
};
static struct gpio_led guruplug_led_pins[] = {
{
.name = "guruplug:red:health",
.gpio = 46,
.active_low = 1,
},
{
.name = "guruplug:green:health",
.gpio = 47,
.active_low = 1,
},
{
.name = "guruplug:red:wmode",
.gpio = 48,
.active_low = 1,
},
{
.name = "guruplug:green:wmode",
.gpio = 49,
.active_low = 1,
},
};
static struct gpio_led_platform_data guruplug_led_data = {
.leds = guruplug_led_pins,
.num_leds = ARRAY_SIZE(guruplug_led_pins),
};
static struct platform_device guruplug_leds = {
.name = "leds-gpio",
.id = -1,
.dev = {
.platform_data = &guruplug_led_data,
}
};
static unsigned int guruplug_mpp_config[] __initdata = {
MPP46_GPIO, /* M_RLED */
MPP47_GPIO, /* M_GLED */
MPP48_GPIO, /* B_RLED */
MPP49_GPIO, /* B_GLED */
0
};
static void __init guruplug_init(void)
{
/*
* Basic setup. Needs to be called early.
*/
kirkwood_init();
kirkwood_mpp_conf(guruplug_mpp_config);
kirkwood_uart0_init();
kirkwood_nand_init(ARRAY_AND_SIZE(guruplug_nand_parts), 25);
kirkwood_ehci_init();
kirkwood_ge00_init(&guruplug_ge00_data);
kirkwood_ge01_init(&guruplug_ge01_data);
kirkwood_sata_init(&guruplug_sata_data);
kirkwood_sdio_init(&guruplug_mvsdio_data);
platform_device_register(&guruplug_leds);
}
MACHINE_START(GURUPLUG, "Marvell GuruPlug Reference Board")
/* Maintainer: Siddarth Gore <gores@marvell.com> */
.atag_offset = 0x100,
.init_machine = guruplug_init,
.map_io = kirkwood_map_io,
.init_early = kirkwood_init_early,
.init_irq = kirkwood_init_irq,
.timer = &kirkwood_timer,
.restart = kirkwood_restart,
MACHINE_END