Staging
v0.7.0
v0.7.0
https://github.com/torvalds/linux
Tip revision: fdf0eaf11452d72945af31804e2a1048ee1b574c authored by Linus Torvalds on 16 July 2023, 22:10:37 UTC
Linux 6.5-rc2
Linux 6.5-rc2
Tip revision: fdf0eaf
samsung,exynos-bus.yaml
# SPDX-License-Identifier: GPL-2.0
%YAML 1.2
---
$id: http://devicetree.org/schemas/interconnect/samsung,exynos-bus.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Samsung Exynos SoC Bus and Interconnect
maintainers:
- Chanwoo Choi <cw00.choi@samsung.com>
- Krzysztof Kozlowski <krzk@kernel.org>
description: |
The Samsung Exynos SoC has many buses for data transfer between DRAM and
sub-blocks in SoC. Most Exynos SoCs share the common architecture for buses.
Generally, each bus of Exynos SoC includes a source clock and a power line,
which are able to change the clock frequency of the bus in runtime. To
monitor the usage of each bus in runtime, the driver uses the PPMU (Platform
Performance Monitoring Unit), which is able to measure the current load of
sub-blocks.
The Exynos SoC includes the various sub-blocks which have the each AXI bus.
The each AXI bus has the owned source clock but, has not the only owned power
line. The power line might be shared among one more sub-blocks. So, we can
divide into two type of device as the role of each sub-block. There are two
type of bus devices as following::
- parent bus device
- passive bus device
Basically, parent and passive bus device share the same power line. The
parent bus device can only change the voltage of shared power line and the
rest bus devices (passive bus device) depend on the decision of the parent
bus device. If there are three blocks which share the VDD_xxx power line,
Only one block should be parent device and then the rest blocks should depend
on the parent device as passive device.
VDD_xxx |--- A block (parent)
|--- B block (passive)
|--- C block (passive)
There are a little different composition among Exynos SoC because each Exynos
SoC has different sub-blocks. Therefore, such difference should be specified
in devicetree file instead of each device driver. In result, this driver is
able to support the bus frequency for all Exynos SoCs.
Detailed correlation between sub-blocks and power line according
to Exynos SoC::
- In case of Exynos3250, there are two power line as following::
VDD_MIF |--- DMC (Dynamic Memory Controller)
VDD_INT |--- LEFTBUS (parent device)
|--- PERIL
|--- MFC
|--- G3D
|--- RIGHTBUS
|--- PERIR
|--- FSYS
|--- LCD0
|--- PERIR
|--- ISP
|--- CAM
- MIF bus's frequency/voltage table
-----------------------
|Lv| Freq | Voltage |
-----------------------
|L1| 50000 |800000 |
|L2| 100000 |800000 |
|L3| 134000 |800000 |
|L4| 200000 |825000 |
|L5| 400000 |875000 |
-----------------------
- INT bus's frequency/voltage table
----------------------------------------------------------
|Block|LEFTBUS|RIGHTBUS|MCUISP |ISP |PERIL ||VDD_INT |
| name| |LCD0 | | | || |
| | |FSYS | | | || |
| | |MFC | | | || |
----------------------------------------------------------
|Mode |*parent|passive |passive|passive|passive|| |
----------------------------------------------------------
|Lv |Frequency ||Voltage |
----------------------------------------------------------
|L1 |50000 |50000 |50000 |50000 |50000 ||900000 |
|L2 |80000 |80000 |80000 |80000 |80000 ||900000 |
|L3 |100000 |100000 |100000 |100000 |100000 ||1000000 |
|L4 |134000 |134000 |200000 |200000 | ||1000000 |
|L5 |200000 |200000 |400000 |300000 | ||1000000 |
----------------------------------------------------------
- In case of Exynos4210, there is one power line as following::
VDD_INT |--- DMC (parent device, Dynamic Memory Controller)
|--- LEFTBUS
|--- PERIL
|--- MFC(L)
|--- G3D
|--- TV
|--- LCD0
|--- RIGHTBUS
|--- PERIR
|--- MFC(R)
|--- CAM
|--- FSYS
|--- GPS
|--- LCD0
|--- LCD1
- In case of Exynos4x12, there are two power line as following::
VDD_MIF |--- DMC (Dynamic Memory Controller)
VDD_INT |--- LEFTBUS (parent device)
|--- PERIL
|--- MFC(L)
|--- G3D
|--- TV
|--- IMAGE
|--- RIGHTBUS
|--- PERIR
|--- MFC(R)
|--- CAM
|--- FSYS
|--- GPS
|--- LCD0
|--- ISP
- In case of Exynos5422, there are two power line as following::
VDD_MIF |--- DREX 0 (parent device, DRAM EXpress controller)
|--- DREX 1
VDD_INT |--- NoC_Core (parent device)
|--- G2D
|--- G3D
|--- DISP1
|--- NoC_WCORE
|--- GSCL
|--- MSCL
|--- ISP
|--- MFC
|--- GEN
|--- PERIS
|--- PERIC
|--- FSYS
|--- FSYS2
- In case of Exynos5433, there is VDD_INT power line as following::
VDD_INT |--- G2D (parent device)
|--- MSCL
|--- GSCL
|--- JPEG
|--- MFC
|--- HEVC
|--- BUS0
|--- BUS1
|--- BUS2
|--- PERIS (Fixed clock rate)
|--- PERIC (Fixed clock rate)
|--- FSYS (Fixed clock rate)
properties:
compatible:
enum:
- samsung,exynos-bus
clocks:
maxItems: 1
clock-names:
items:
- const: bus
devfreq:
$ref: /schemas/types.yaml#/definitions/phandle
description:
Parent bus device. Valid and required only for the passive bus devices.
devfreq-events:
$ref: /schemas/types.yaml#/definitions/phandle-array
minItems: 1
maxItems: 4
description:
Devfreq-event device to monitor the current utilization of buses. Valid
and required only for the parent bus devices.
exynos,saturation-ratio:
$ref: /schemas/types.yaml#/definitions/uint32
description:
Percentage value which is used to calibrate the performance count against
total cycle count. Valid only for the parent bus devices.
'#interconnect-cells':
const: 0
interconnects:
minItems: 1
maxItems: 2
operating-points-v2: true
opp-table:
type: object
samsung,data-clock-ratio:
$ref: /schemas/types.yaml#/definitions/uint32
default: 8
description:
Ratio of the data throughput in B/s to minimum data clock frequency in
Hz.
vdd-supply:
description:
Main bus power rail. Valid and required only for the parent bus devices.
required:
- compatible
- clocks
- clock-names
- operating-points-v2
additionalProperties: false
examples:
- |
#include <dt-bindings/clock/exynos3250.h>
bus-dmc {
compatible = "samsung,exynos-bus";
clocks = <&cmu_dmc CLK_DIV_DMC>;
clock-names = "bus";
operating-points-v2 = <&bus_dmc_opp_table>;
devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
vdd-supply = <&buck1_reg>;
bus_dmc_opp_table: opp-table {
compatible = "operating-points-v2";
opp-50000000 {
opp-hz = /bits/ 64 <50000000>;
opp-microvolt = <800000>;
};
opp-100000000 {
opp-hz = /bits/ 64 <100000000>;
opp-microvolt = <800000>;
};
opp-134000000 {
opp-hz = /bits/ 64 <134000000>;
opp-microvolt = <800000>;
};
opp-200000000 {
opp-hz = /bits/ 64 <200000000>;
opp-microvolt = <825000>;
};
opp-400000000 {
opp-hz = /bits/ 64 <400000000>;
opp-microvolt = <875000>;
};
};
};
ppmu_dmc0: ppmu@106a0000 {
compatible = "samsung,exynos-ppmu";
reg = <0x106a0000 0x2000>;
events {
ppmu_dmc0_3: ppmu-event3-dmc0 {
event-name = "ppmu-event3-dmc0";
};
};
};
bus_leftbus: bus-leftbus {
compatible = "samsung,exynos-bus";
clocks = <&cmu CLK_DIV_GDL>;
clock-names = "bus";
operating-points-v2 = <&bus_leftbus_opp_table>;
devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
vdd-supply = <&buck3_reg>;
};
bus-rightbus {
compatible = "samsung,exynos-bus";
clocks = <&cmu CLK_DIV_GDR>;
clock-names = "bus";
operating-points-v2 = <&bus_leftbus_opp_table>;
devfreq = <&bus_leftbus>;
};
- |
dmc: bus-dmc {
compatible = "samsung,exynos-bus";
clocks = <&clock CLK_DIV_DMC>;
clock-names = "bus";
operating-points-v2 = <&bus_dmc_opp_table>;
samsung,data-clock-ratio = <4>;
#interconnect-cells = <0>;
devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
vdd-supply = <&buck1_reg>;
};
leftbus: bus-leftbus {
compatible = "samsung,exynos-bus";
clocks = <&clock CLK_DIV_GDL>;
clock-names = "bus";
operating-points-v2 = <&bus_leftbus_opp_table>;
interconnects = <&dmc>;
#interconnect-cells = <0>;
devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
vdd-supply = <&buck3_reg>;
};
display: bus-display {
compatible = "samsung,exynos-bus";
clocks = <&clock CLK_DIV_ACLK_266>;
clock-names = "bus";
operating-points-v2 = <&bus_display_opp_table>;
interconnects = <&leftbus &dmc>;
#interconnect-cells = <0>;
devfreq = <&leftbus>;
};