Staging
v0.7.0
v0.7.0
nvidia,tegra20-usb-phy.txt
Tegra SOC USB PHY
The device node for Tegra SOC USB PHY:
Required properties :
- compatible : For Tegra20, must contain "nvidia,tegra20-usb-phy".
For Tegra30, must contain "nvidia,tegra30-usb-phy". Otherwise, must contain
"nvidia,<chip>-usb-phy" plus at least one of the above, where <chip> is
tegra114, tegra124, tegra132, or tegra210.
- reg : Defines the following set of registers, in the order listed:
- The PHY's own register set.
Always present.
- The register set of the PHY containing the UTMI pad control registers.
Present if-and-only-if phy_type == utmi.
- phy_type : Should be one of "utmi", "ulpi" or "hsic".
- clocks : Defines the clocks listed in the clock-names property.
- clock-names : The following clock names must be present:
- reg: The clock needed to access the PHY's own registers. This is the
associated EHCI controller's clock. Always present.
- pll_u: PLL_U. Always present.
- timer: The timeout clock (clk_m). Present if phy_type == utmi.
- utmi-pads: The clock needed to access the UTMI pad control registers.
Present if phy_type == utmi.
- ulpi-link: The clock Tegra provides to the ULPI PHY (cdev2).
Present if phy_type == ulpi, and ULPI link mode is in use.
- resets : Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names : Must include the following entries:
- usb: The PHY's own reset signal.
- utmi-pads: The reset of the PHY containing the chip-wide UTMI pad control
registers. Required even if phy_type == ulpi.
Required properties for phy_type == ulpi:
- nvidia,phy-reset-gpio : The GPIO used to reset the PHY.
Required PHY timing params for utmi phy, for all chips:
- nvidia,hssync-start-delay : Number of 480 Mhz clock cycles to wait before
start of sync launches RxActive
- nvidia,elastic-limit : Variable FIFO Depth of elastic input store
- nvidia,idle-wait-delay : Number of 480 Mhz clock cycles of idle to wait
before declare IDLE.
- nvidia,term-range-adj : Range adjusment on terminations
- Either one of the following for HS driver output control:
- nvidia,xcvr-setup : integer, uses the provided value.
- nvidia,xcvr-setup-use-fuses : boolean, indicates that the value is read
from the on-chip fuses
If both are provided, nvidia,xcvr-setup-use-fuses takes precedence.
- nvidia,xcvr-lsfslew : LS falling slew rate control.
- nvidia,xcvr-lsrslew : LS rising slew rate control.
Required PHY timing params for utmi phy, only on Tegra30 and above:
- nvidia,xcvr-hsslew : HS slew rate control.
- nvidia,hssquelch-level : HS squelch detector level.
- nvidia,hsdiscon-level : HS disconnect detector level.
Optional properties:
- nvidia,has-legacy-mode : boolean indicates whether this controller can
operate in legacy mode (as APX 2500 / 2600). In legacy mode some
registers are accessed through the APB_MISC base address instead of
the USB controller.
- nvidia,is-wired : boolean. Indicates whether we can do certain kind of power
optimizations for the devices that are always connected. e.g. modem.
- dr_mode : dual role mode. Indicates the working mode for the PHY. Can be
"host", "peripheral", or "otg". Defaults to "host" if not defined.
host means this is a host controller
peripheral means it is device controller
otg means it can operate as either ("on the go")
- nvidia,has-utmi-pad-registers : boolean indicates whether this controller
contains the UTMI pad control registers common to all USB controllers.
VBUS control (required for dr_mode == otg, optional for dr_mode == host):
- vbus-supply: regulator for VBUS