Staging
v0.7.0
v0.7.0
https://github.com/torvalds/linux
Tip revision: dfd42facf1e4ada021b939b4e19c935dcdd55566 authored by Linus Torvalds on 06 February 2022, 20:20:50 UTC
Linux 5.17-rc3
Linux 5.17-rc3
Tip revision: dfd42fa
nxp,imx8mq-mipi-csi2.yaml
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/media/nxp,imx8mq-mipi-csi2.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: NXP i.MX8MQ MIPI CSI-2 receiver
maintainers:
- Martin Kepplinger <martin.kepplinger@puri.sm>
description: |-
This binding covers the CSI-2 RX PHY and host controller included in the
NXP i.MX8MQ SoC. It handles the sensor/image input and process for all the
input imaging devices.
properties:
compatible:
enum:
- fsl,imx8mq-mipi-csi2
reg:
maxItems: 1
clocks:
items:
- description: core is the RX Controller Core Clock input. This clock
must be exactly equal to or faster than the receive
byteclock from the RX DPHY.
- description: esc is the Rx Escape Clock. This must be the same escape
clock that the RX DPHY receives.
- description: ui is the pixel clock (phy_ref up to 333Mhz).
See the reference manual for details.
clock-names:
items:
- const: core
- const: esc
- const: ui
power-domains:
maxItems: 1
resets:
items:
- description: CORE_RESET reset register bit definition
- description: PHY_REF_RESET reset register bit definition
- description: ESC_RESET reset register bit definition
fsl,mipi-phy-gpr:
description: |
The phandle to the imx8mq syscon iomux-gpr with the register
for setting RX_ENABLE for the mipi receiver.
The format should be as follows:
<gpr req_gpr>
gpr is the phandle to general purpose register node.
req_gpr is the gpr register offset of RX_ENABLE for the mipi phy.
$ref: /schemas/types.yaml#/definitions/phandle-array
items:
items:
- description: The 'gpr' is the phandle to general purpose register node.
- description: The 'req_gpr' is the gpr register offset containing
CSI2_1_RX_ENABLE or CSI2_2_RX_ENABLE respectively.
maximum: 0xff
interconnects:
maxItems: 1
interconnect-names:
const: dram
ports:
$ref: /schemas/graph.yaml#/properties/ports
properties:
port@0:
$ref: /schemas/graph.yaml#/$defs/port-base
unevaluatedProperties: false
description:
Input port node, single endpoint describing the CSI-2 transmitter.
properties:
endpoint:
$ref: video-interfaces.yaml#
unevaluatedProperties: false
properties:
data-lanes:
minItems: 1
items:
- const: 1
- const: 2
- const: 3
- const: 4
required:
- data-lanes
port@1:
$ref: /schemas/graph.yaml#/properties/port
description:
Output port node
required:
- port@0
- port@1
required:
- compatible
- reg
- clocks
- clock-names
- power-domains
- resets
- fsl,mipi-phy-gpr
- ports
additionalProperties: false
examples:
- |
#include <dt-bindings/clock/imx8mq-clock.h>
#include <dt-bindings/interconnect/imx8mq.h>
#include <dt-bindings/reset/imx8mq-reset.h>
csi@30a70000 {
compatible = "fsl,imx8mq-mipi-csi2";
reg = <0x30a70000 0x1000>;
clocks = <&clk IMX8MQ_CLK_CSI1_CORE>,
<&clk IMX8MQ_CLK_CSI1_ESC>,
<&clk IMX8MQ_CLK_CSI1_PHY_REF>;
clock-names = "core", "esc", "ui";
assigned-clocks = <&clk IMX8MQ_CLK_CSI1_CORE>,
<&clk IMX8MQ_CLK_CSI1_PHY_REF>,
<&clk IMX8MQ_CLK_CSI1_ESC>;
assigned-clock-rates = <266000000>, <200000000>, <66000000>;
assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_266M>,
<&clk IMX8MQ_SYS2_PLL_1000M>,
<&clk IMX8MQ_SYS1_PLL_800M>;
power-domains = <&pgc_mipi_csi1>;
resets = <&src IMX8MQ_RESET_MIPI_CSI1_CORE_RESET>,
<&src IMX8MQ_RESET_MIPI_CSI1_PHY_REF_RESET>,
<&src IMX8MQ_RESET_MIPI_CSI1_ESC_RESET>;
fsl,mipi-phy-gpr = <&iomuxc_gpr 0x88>;
interconnects = <&noc IMX8MQ_ICM_CSI1 &noc IMX8MQ_ICS_DRAM>;
interconnect-names = "dram";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
imx8mm_mipi_csi_in: endpoint {
remote-endpoint = <&imx477_out>;
data-lanes = <1 2 3 4>;
};
};
port@1 {
reg = <1>;
imx8mm_mipi_csi_out: endpoint {
remote-endpoint = <&csi_in>;
};
};
};
};
...